Source Technologies ST9530 manual Sar$, SQ1200$200, SQ6October 5, 2005$, Terminator, SQ4$2104.44~

Page 47

The commands in Figure 8.1 in order of appearance. (Audit Report fields shown in bold)

&&??&%

Hex transfer enable.

&%STFPASSWORD$

Password command.

&%SMCP0001$

MICR definition command with the count set to one.

&%SAR$

Activates Audit Report recording.

&%STP10001$

Unlock flash resource number 10001.

&%STP00200$

Unlock flash resource number 200.

&%1B26...3358$

PCL sequence in hex which sets the page format and enables

 

macro number 10001.

&%SQ1200$200

Stores the vendor number 200 in the first position of the Audit

 

Report. Note that this field will not be sent to the page to be

 

printed. Here we send the field again so that it will print.

&%1B$(s1p16v0s3b4148T

PCL sequence which changes the font to Univers 16 point.

 

After the check serial numbers prints (100), the printer is

 

returned to its default font with the following command.

&%1B$(3@

PCL command to return to default font.

&%SQ6October 5, 2005$

Stores the date in the sixth position of the Audit Report.

&%SMF$2014.44~

Prints Secure Font command. NOTE: Tilde (~) is command

 

terminator.

&%1B$(s0p12h10v1s0b4099T PCL command to change the font to Courier 12 pitch Italic. See print PCL Fonts on the Front Panel under the test menu for a printout with their call commands.

&%1B$(3@

PCL command to return to the default font.

&%SQ4$2104.44~

Stores the amount in the fourth position of the Audit Report.

&%SQ3Vendor Systems $ Stores the payee, Vendor Systems, in the third position of the Audit Trail report.

Secure MICR Printer User’s Guide

43

© Source Technologies

September 2005

All Rights Reserved

Image 47
Contents ST9530 Secure Micr Printer User’s Guide Page Table of Contents Audit Trail Report Error MessagesPrinter Installation Micr Printing Today Micr OverviewCheck Processing System Secure Micr Printer User’s Guide Design Elements in Detail Paper General Features of Check DesignPosition and Dimension Gauge Micr Check DesignAmount Convenience Amount DuplexingMicr Clear Band Data Elements DateDrawee Institution Name Amount In WordsPayee Area Signature AreaExternal Processing Code EPC Field Position Memo LineCheck Serial Number Fractional Routing Number Micr Line Auxiliary On-Us Field Positions 65 toOn-Us Field Positions 32 to Sample Check Quality Issues Layout WeightMicr Check Stock QualityCheck Stock Security Features Security IssuesSecurity Note Secure Micr Printer User’s Guide Secure Fonts Micr FeaturesMicr Mode Micr Fonts@PJL Ustatus Device CODE=40020 MicroPrintBi-Directional Feedback Micr Menu Resource StorageSTF Command Entering Micr ModeSmcp STH CommandPassword Micr Definition Command SMCPxxxx$ optionalPrint Micr E-13B Font SMDddd...ddd$ Set New Password Command &%STExxxxxxxx$STE STSPrint MicroPrint Line SMMxxxxxxxxx!$ Print Micr CMC7 Font SM7ddd...ddd$Print Secure Numeric Font SMFddd..ddd~ Print ICR Secure Numeric Font &%SMIxxxxxx~Format Flash Memory SFF$ Secure Flash Resource Unlock Command STPxxxxx$Tray Lock Command STTL#$ Load Flash Resource STLxxxxxyyyyyyzdd....ddSttson Tray Unlock Command STTU#$Tray Swapping Commands STTU#DES and AES Decryption Decryption CommandsTurn AES Decryption OFF Turn DES Decryption onTurn AES Decryption on Turn DES Decryption OFFCustomer Character Conversation Command STBEEP2$ Special Alert and Custom Beep CommandSTBEEP1$ MICRpoint Feature Secure Micr Printer User’s Guide Turning Hex Transfer Off IBM Host Programming Features and ExamplesHex Transfer Turning Hex Transfer OnHex Transfer Examples Micr Mode Command Example Micr font character mapping in Appendix a Commands in .1 in order of appearanceSTFPASSWORD$ Command terminatorExample &%STY2300$ Escape Character TranslationSTY4040$ STY4000$Sample Check Audit Trail Reports End Audit Record Audit Trail Report Command SetPrint Audit Report SARAudit Report Field Four SQ4d..d~ Audit Report Field One SQ1d..d$Audit Report Field Two-MICR Line Audit Report Field Three SQ3d..d$Print and Purge Audit Report &%SPURGExx$ Audit Report Field Five SQ5d..d$Audit Report Field Six SQ6d..d$ Audit Report Field Seven SQ7d..d$Print Audit Report SPRINTxx$ Start Audit Feedback CommandAudit Trail Commands Example Audit Trail Check Sample Terminator SAR$SQ1200$200 SQ6October 5, 2005$SQ7103345 AM$ SMD...$Msmith Action Error MessagesError Message on Display Printed Message DescriptionMacro Definition Error Invalid decode Page Example &%SMD 00001234 T01234567T3210987654321$ Will print Appendix a E13B Micr Font Mapping Command&%SMDddd..ddd$Appendix B CMC7 Micr Font Mapping Less Than Equal Greater Than Description Alpha/Numeric Hex Value Secure Font Character Appendix C Secure Numeric Font MappingTwo Three Four Five Six Seven Eight Nine Arrow Example&%SMF$15,575.00~ Appendix D ICR Secure Numeric Font Mapping Appendix E Micr Mode Command Summary STTSOFF$ Previous Audit Report information will be lost SPRINT$STORE$ SPURGE$Appendix G PJL Based Micr Commands PJL Re-Lock Sequence With a New Password Value @PJL Info Micr UELCartridge Status = Unknown PCL Font Calls, Positioning Commands and Variable Print Data Sample Accounts Payable Check PJL and PCL commands used to print the sample check ESC%-12345X@PJL Ldeletepassword LRESOURCEflash