Source Technologies ST9530 Audit Report Field One SQ1d..d$, Audit Report Field Two-MICR Line

Page 42

$	Command terminator

Ends the Audit Record and the PJL job (ignored if there was no Start Audit Record Command).

Audit Report Field One	&%SQ1d..d$
&%SQ1	Lead in sequence
d..d	Data to be stored
$	Command terminator

This command identifies the data to be printed in the first column of the report. It is a maximum of 14 characters in length. If less than 14 characters are sent, the printer fills the field with spaces when the audit report is printed. This field is recorded in the audit report only, it is not printed on the check.

Audit Report Field Two-MICR Line	&%SMDd..d$ or &%SM7d..d$
&%SMD or &%SM7	Lead in sequence
d..d	Data to be printed
$	Command terminator

This command identifies the data to be printed in the second column of the report. It is a maximum of 40 characters in length.

Audit Report Field Three	&%SQ3d..d$
&%SQ3	Lead in sequence
d..d	Data to be printed
$	Command terminator

This command identifies the data to be printed in the third column of the report. It is a maximum of 40 characters.

Audit Report Field Four	&%SQ4d..d~
&%SQ4	Lead in sequence
d..d	Data to be printed
~	Command terminator

This command identifies the data to be printed in the fourth column of the report. It is a maximum of 16 characters in length. Since a total of this field can be provided at the end of the Audit Trail Report it is typically used for the convenience amount field. NOTE: This is the only command where the $ is not a command terminator. The tilde ~ (hex 7E) acts as the command terminator.

Secure MICR Printer User’s Guide	38	© Source Technologies
September 2005	38	All Rights Reserved

Image 42

Contents ST9530 Secure Micr Printer User’s Guide Page Table of Contents Error Messages Audit Trail ReportPrinter Installation Micr Overview Check Processing SystemMicr Printing Today Secure Micr Printer User’s Guide Micr Check Design General Features of Check DesignPosition and Dimension Gauge Design Elements in Detail PaperData Elements Date DuplexingMicr Clear Band Amount Convenience AmountSignature Area Amount In WordsPayee Area Drawee Institution NameAuxiliary On-Us Field Positions 65 to Memo LineCheck Serial Number Fractional Routing Number Micr Line External Processing Code EPC Field PositionOn-Us Field Positions 32 to Sample Check Quality Issues Quality WeightMicr Check Stock LayoutSecurity Issues Check Stock Security FeaturesSecurity Note Secure Micr Printer User’s Guide Micr Fonts Micr FeaturesMicr Mode Secure FontsMicroPrint Bi-Directional Feedback@PJL Ustatus Device CODE=40020 Resource Storage Micr MenuEntering Micr Mode STF CommandMicr Definition Command SMCPxxxx$ optional STH CommandPassword SmcpSTS Set New Password Command &%STExxxxxxxx$STE Print Micr E-13B Font SMDddd...ddd$Print ICR Secure Numeric Font &%SMIxxxxxx~ Print Micr CMC7 Font SM7ddd...ddd$Print Secure Numeric Font SMFddd..ddd~ Print MicroPrint Line SMMxxxxxxxxx!$Load Flash Resource STLxxxxxyyyyyyzdd....dd Secure Flash Resource Unlock Command STPxxxxx$Tray Lock Command STTL#$ Format Flash Memory SFF$STTU# Tray Unlock Command STTU#$Tray Swapping Commands SttsonDecryption Commands DES and AES DecryptionTurn DES Decryption OFF Turn DES Decryption onTurn AES Decryption on Turn AES Decryption OFFCustomer Character Conversation Command Special Alert and Custom Beep Command STBEEP1$STBEEP2$ MICRpoint Feature Secure Micr Printer User’s Guide Turning Hex Transfer On IBM Host Programming Features and ExamplesHex Transfer Turning Hex Transfer OffHex Transfer Examples Micr Mode Command Example Command terminator Commands in .1 in order of appearanceSTFPASSWORD$ Micr font character mapping in Appendix aSTY4000$ Escape Character TranslationSTY4040$ Example &%STY2300$Sample Check Audit Trail Reports SAR Audit Trail Report Command SetPrint Audit Report End Audit RecordAudit Report Field Three SQ3d..d$ Audit Report Field One SQ1d..d$Audit Report Field Two-MICR Line Audit Report Field Four SQ4d..d~Audit Report Field Seven SQ7d..d$ Audit Report Field Five SQ5d..d$Audit Report Field Six SQ6d..d$ Print and Purge Audit Report &%SPURGExx$Start Audit Feedback Command Print Audit Report SPRINTxx$Audit Trail Commands Example Audit Trail Check Sample SQ6October 5, 2005$ SAR$SQ1200$200 TerminatorSMD...$ SQ7103345 AM$Msmith Description Error MessagesError Message on Display Printed Message ActionMacro Definition Error Invalid decode Page Appendix a E13B Micr Font Mapping Command&%SMDddd..ddd$ Example &%SMD 00001234 T01234567T3210987654321$ Will printAppendix B CMC7 Micr Font Mapping Less Than Equal Greater Than Appendix C Secure Numeric Font Mapping Description Alpha/Numeric Hex Value Secure Font CharacterTwo Three Four Five Six Seven Eight Nine Arrow Example&%SMF$15,575.00~ Appendix D ICR Secure Numeric Font Mapping Appendix E Micr Mode Command Summary STTSOFF$ SPURGE$ SPRINT$STORE$ Previous Audit Report information will be lostAppendix G PJL Based Micr Commands PJL Re-Lock Sequence With a New Password Value UEL @PJL Info MicrCartridge Status = Unknown PCL Font Calls, Positioning Commands and Variable Print Data Sample Accounts Payable Check PJL and PCL commands used to print the sample check ESC%-12345X@PJL Ldeletepassword LRESOURCEflash