Source Technologies ST9530 manual Printer Installation

Page 5

1. Printer Installation

For complete information on how to unpack and setup your printer, see your printer’s user’s guide. Please read the following if you are going to install the printer driver shipped with your printer.

1.Locate the CD that was shipped with your printer.

Note: If you do not have a CD-ROM drive on the host PC, locate another computer with a CD-ROM drive, start the CD-ROM utility, and then follow the instructions on the screen to create printer driver diskettes.

2.Follow the instructions in the CD booklet to start the printer setup utility appropriate for your operating system, i.e. Windows 95, NT, etc. The setup utility will install printer driver and utilities to manage Source Technologies printer(s) attached to your PC or Network.

3.The Source Technologies MICR printer, in most cases, assumes the printer driver is set to the internal DEFAULT values. The following Default values should not be changed for best overall printer performance and data stream requirements of the ST Secure MICR printer.

-Print Resolution under the Graphic Tab should be set to the Default value of 600 DPI.

-Form Source under the Paper Tab should be set to Default value of By Source.

-Print Quality and Picture Grade under the Graphic Tab should be set to the Default values of Use Printer Default.

The ST Secure MICR Printer requires a PCL5 or PCL5e data stream. Current level printer drivers require Graphic Mode under the Graphic Tab be set to either Raster or GL/2. We recommend Raster. This is the only required non-Default value that needs to be set in the printer driver.

A majority of other driver options can be set for your particular requirements. The most obvious of these would be a Paper Tray selection if your application uses the Print Driver Setting.

Secure MICR Printer User’s Guide	1	© Source Technologies
September 2005	1	All Rights Reserved

Image 5

Contents ST9530 Secure Micr Printer User’s Guide Page Table of Contents Audit Trail Report Error MessagesPrinter Installation Micr Printing Today Micr OverviewCheck Processing System Secure Micr Printer User’s Guide Position and Dimension Gauge General Features of Check DesignMicr Check Design Design Elements in Detail PaperMicr Clear Band DuplexingData Elements Date Amount Convenience AmountPayee Area Amount In WordsSignature Area Drawee Institution NameCheck Serial Number Fractional Routing Number Micr Line Memo LineAuxiliary On-Us Field Positions 65 to External Processing Code EPC Field PositionOn-Us Field Positions 32 to Sample Check Quality Issues Micr Check Stock WeightQuality LayoutCheck Stock Security Features Security IssuesSecurity Note Secure Micr Printer User’s Guide Micr Mode Micr FeaturesMicr Fonts Secure Fonts@PJL Ustatus Device CODE=40020 MicroPrintBi-Directional Feedback Micr Menu Resource StorageSTF Command Entering Micr ModePassword STH CommandMicr Definition Command SMCPxxxx$ optional SmcpSTE Set New Password Command &%STExxxxxxxx$STS Print Micr E-13B Font SMDddd...ddd$Print Secure Numeric Font SMFddd..ddd~ Print Micr CMC7 Font SM7ddd...ddd$Print ICR Secure Numeric Font &%SMIxxxxxx~ Print MicroPrint Line SMMxxxxxxxxx!$Tray Lock Command STTL#$ Secure Flash Resource Unlock Command STPxxxxx$Load Flash Resource STLxxxxxyyyyyyzdd....dd Format Flash Memory SFF$Tray Swapping Commands Tray Unlock Command STTU#$STTU# SttsonDES and AES Decryption Decryption CommandsTurn AES Decryption on Turn DES Decryption onTurn DES Decryption OFF Turn AES Decryption OFFCustomer Character Conversation Command STBEEP2$ Special Alert and Custom Beep CommandSTBEEP1$ MICRpoint Feature Secure Micr Printer User’s Guide Hex Transfer IBM Host Programming Features and ExamplesTurning Hex Transfer On Turning Hex Transfer OffHex Transfer Examples Micr Mode Command Example STFPASSWORD$ Commands in .1 in order of appearanceCommand terminator Micr font character mapping in Appendix aSTY4040$ Escape Character TranslationSTY4000$ Example &%STY2300$Sample Check Audit Trail Reports Print Audit Report Audit Trail Report Command SetSAR End Audit RecordAudit Report Field Two-MICR Line Audit Report Field One SQ1d..d$Audit Report Field Three SQ3d..d$ Audit Report Field Four SQ4d..d~Audit Report Field Six SQ6d..d$ Audit Report Field Five SQ5d..d$Audit Report Field Seven SQ7d..d$ Print and Purge Audit Report &%SPURGExx$Print Audit Report SPRINTxx$ Start Audit Feedback CommandAudit Trail Commands Example Audit Trail Check Sample SQ1200$200 SAR$SQ6October 5, 2005$ TerminatorSQ7103345 AM$ SMD...$Msmith Error Message on Display Printed Message Error MessagesDescription ActionMacro Definition Error Invalid decode Page Example &%SMD 00001234 T01234567T3210987654321$ Will print Appendix a E13B Micr Font Mapping Command&%SMDddd..ddd$Appendix B CMC7 Micr Font Mapping Less Than Equal Greater Than Description Alpha/Numeric Hex Value Secure Font Character Appendix C Secure Numeric Font MappingTwo Three Four Five Six Seven Eight Nine Arrow Example&%SMF$15,575.00~ Appendix D ICR Secure Numeric Font Mapping Appendix E Micr Mode Command Summary STTSOFF$ STORE$ SPRINT$SPURGE$ Previous Audit Report information will be lostAppendix G PJL Based Micr Commands PJL Re-Lock Sequence With a New Password Value @PJL Info Micr UELCartridge Status = Unknown PCL Font Calls, Positioning Commands and Variable Print Data Sample Accounts Payable Check PJL and PCL commands used to print the sample check ESC%-12345X@PJL Ldeletepassword LRESOURCEflash