Advantech PPC-155T user manual Preparing for First-time Use, Installation Procedures

Page 22

2.2Preparing for First-time Use

Before commencing set up of the panel PC system, the following items should be available:

!Keyboard

!Mouse (for system software installation)

2.3Installation Procedures

2.3.1Connecting the power cord

The panel PC can only be powered through an AC electrical outlet (100 ~ 250 volts, 50 ~ 60 Hz). Be sure to handle the power cords by holding the plug ends only.

Follow these procedures in order:

1.Connect the female end of the power cord to the AC inlet of the panel PC.

2.Connect the 3-pin male plug of the power cord to an electrical outlet.

2.3.2Connecting the keyboard and mouse

Connect the PS/2 mouse and keyboard to the I/O section of PPC.

If using a serial mouse and the panel PC has a touchscreen, it is possible to connect the mouse to any COM port except COM4.

2.3.3Switching on the power

Switch on the power switch, which is located inside the bottom side cover.

2.4Running the BIOS Setup Program

The panel PC will be properly set up and configured by the dealer prior to delivery. However, it may be necessary to use the panel PC's BIOS (Basic Input-Output Sys- tem) setup program to change the system configuration information, such as the cur- rent date and time, or the type of hard drive. The setup program is stored in read-only memory (ROM). It can be accessed either when you turn on or reset the panel PC, by pressing the “Del” key on your keyboard immediately after powering on the computer.

The settings specified with the setup program are recorded in a special area of mem- ory called “CMOS RAM.” This memory is backed up by a battery so that it will not be erased after turning off or resetting the system. Whenever the power is turned on, the system reads the settings stored in CMOS RAM and compares them to the equip- ment check conducted during the power on self-test (POST). If a problem occurs, an error message will be displayed on screen, and the computer prompts the user to run the setup program.

PPC-155T User Manual

10

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PPC-155T Copyright Acknowledgements Product Warranty 2 years Declaration of ConformityTechnical Support and Assistance FCC Class BDocument Feedback Packing ListAdditional Information and Assistance Contact informationSafety Instructions Wichtige Sicherheishinweise Safety Precaution Static Electricity Page Using the Panel PC ChapterAppendix a Appendix BChapter General Information SpecificationsIntroduction General Information Certifications Dimensions Dimensions of PPC-155TPage System Setup System Setup Quick Tour of the Panel PCSystem Setup Running the Bios Setup Program Installation ProceduresPreparing for First-time Use Installing System Software Installing the DriversPage Using the Panel PC Using the Panel PC CD-ROM Drive optionalPcmcia PS/2 Mouse and KeyboardPCI Bus Expansion PCI bus expansionVGA Port Serial COM PortsUSB Ports Ethernet Audio InterfaceFront Bezel LED and Light Sensor Touchscreen Optional Page Hardware Installation Jumpers and Connectors Hardware InstallationDisassembling the Panel PC Hardware Installation Installing the 2.5 Hard Disk Drive PPC without the Rear CoverPlugging in the Eide cable Installing the Central Processing Unit CPU Placing the CPU in the socketTightening the screws on the CPU 11 Fastening the CPU module to the motherboard Installing the DDR Sdram Memory Module 12 Placing the memory module in the DimmPage Jumpers Connectors Jumpers & Connectors Setting jumpersJumpers & Connectors Jumper and Connector Locations Connectors Page Driver Installation Driver Installation Driver InstallationUpdating Driver Searching on the Advantech Website Appendix a Appendix a Disassembly Disassembly ProcedureAppendix a Disassembly Figure A.4 The PPC without the rear cover Figure A.6 Unfastening the middle plate Figure A.8 Unfastening the HDD module Figure A.10 Disconnecting the HDD cable Figure A.12 Loosening the screws on the CD-ROM module Figure A.14 Removing the fixed brace Figure A.16 Removing the CD-ROM / Pcmcia slot cover Figure A.18 Disconnecting the CD-ROM connector Figure A.20 Unfastening the CPU socket Figure A.22 Removing the Sdram module Page Appendix B Figure B.1 PCI Card Dimensional Limits Appendix B PCI Card Size Limits
Top Page Image Contents