Advantech PPC-155T user manual Jumpers & Connectors

Page 45

5.1.2.1PCI slot voltage setting (JP2)

The panel PC supports 5V and 3.3V PCI_VIO slot voltages. The default voltage is 3.3V (closed pins 1-2). 5V may be selected by closing jumpers 2-3.

Table 5.1: PCI slot voltage setting (JP2)

3.3V (default)

 

 

5V

 

 

 

 

 

 

 

 

1

2

3

1

2

3

5.1.2.2Clear CMOS (JP3)

This jumper erases the CMOS data and resets the system BIOS information.

Table 5.2: Clear CMOS (JP3)

Normal operation (default)

Clear CMOS

 

 

 

 

 

 

 

 

1

2

3

1

2

3

5.1.2.3LVDS voltage setting (JP5)

The panel PC supports 5V and 3.3V LVDS voltages. The default voltage is 3.3V (closed pins 1-2). 5V may be selected by closing jumpers 2-3.

Table 5.3: LVDS voltage setting (JP5)

3.3V (default)

 

 

5V

 

 

 

 

 

 

 

 

 

1

2

3

1

2

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chapter 5 Jumpers & Connectors

33

PPC-155T User Manual

Image 45
Contents PPC-155T Copyright Acknowledgements Declaration of Conformity Product Warranty 2 yearsFCC Class B Technical Support and AssistancePacking List Document FeedbackContact information Additional Information and AssistanceSafety Instructions Wichtige Sicherheishinweise Safety Precaution Static Electricity Page Chapter Using the Panel PCAppendix B Appendix aChapter Specifications General InformationIntroduction General Information Certifications Dimensions of PPC-155T DimensionsPage System Setup Quick Tour of the Panel PC System SetupSystem Setup Installation Procedures Running the Bios Setup ProgramPreparing for First-time Use Installing the Drivers Installing System SoftwarePage Using the Panel PC CD-ROM Drive optional Using the Panel PCPS/2 Mouse and Keyboard PcmciaPCI bus expansion PCI Bus ExpansionSerial COM Ports VGA PortUSB Ports Audio Interface EthernetFront Bezel LED and Light Sensor Touchscreen Optional Page Hardware Installation Hardware Installation Jumpers and ConnectorsDisassembling the Panel PC Hardware Installation PPC without the Rear Cover Installing the 2.5 Hard Disk DrivePlugging in the Eide cable Placing the CPU in the socket Installing the Central Processing Unit CPUTightening the screws on the CPU 11 Fastening the CPU module to the motherboard 12 Placing the memory module in the Dimm Installing the DDR Sdram Memory ModulePage Jumpers Connectors Setting jumpers Jumpers & ConnectorsJumpers & Connectors Jumper and Connector Locations Connectors Page Driver Installation Driver Installation Driver InstallationUpdating Driver Searching on the Advantech Website Appendix a Disassembly Procedure Appendix a DisassemblyAppendix a Disassembly Figure A.4 The PPC without the rear cover Figure A.6 Unfastening the middle plate Figure A.8 Unfastening the HDD module Figure A.10 Disconnecting the HDD cable Figure A.12 Loosening the screws on the CD-ROM module Figure A.14 Removing the fixed brace Figure A.16 Removing the CD-ROM / Pcmcia slot cover Figure A.18 Disconnecting the CD-ROM connector Figure A.20 Unfastening the CPU socket Figure A.22 Removing the Sdram module Page Appendix B Appendix B PCI Card Size Limits Figure B.1 PCI Card Dimensional Limits