Apple NMB-003 manual Raid, System With Seven Drive Modules

Page 70

A System With Seven Drive Modules

You can use the following RAID levels on an Xserve RAID system with seven drive modules:

mRAID 0

mRAID 1

mRAID 3

mRAID 5

mRAID 30

mRAID 50

Note: This list is representative but does not include all possible schemes.

RAID 0 Schemes

You can use RAID 0 several ways, depending on how you divide the drive modules across the RAID controllers. If all of the modules are on one RAID controller, all drives can be striped together.

RAID 0

Appears

as

Stripe

Disk 1

If four modules are on one controller and three modules are on the other, the drives on each controller can be striped together.

RAID 0

Appears

as

Stripe

Stripe

Disk 1

Disk 2

70 Chapter 8

Image 70
Contents User’s Guide Apple Computer, Inc Apple Computer, Inc. All rights reservedContents Using the Xserve RAID System Installing the SystemConnecting Xserve RAID to a Host System and a Network Installing or Replacing ComponentsData Storage Methods Installing Xserve RAID Hardware and SoftwareConnecting a 14-Drive System to a Host Computer or Switch RAID OverviewGlossary Appendix a Specifications Appendix B Safety, Maintenance, and ErgonomicsAbout This Guide Page Introducing Xserve RAID Unpacking the System Introducing Xserve RAID Your System at a Glance-Front Panel Indicates temperature status green is OK, red is failure Your System at a Glance-Back Panel RAIDRedundant, hot-swappable cooling module cools the system Your System at a Glance-Mounting Hardware Use this bar to fasten extenders C and D for a deep rack Page Precautions for Handling the System Preparing to Install Xserve RAID in a RackGuidelines for Installation Use your leg muscles to liftLift with a smooth motion don’t jerk the load up or down Choosing the System’s Location in the RackElectrical Power Rack StabilityOperating Environment SecurityMounting Xserve RAID in a Rack Getting Ready to Install the System Determine the Position for the System in the Rack Prepare the System for Installation Installing the SystemFollow the instructions in Unpacking the System on Two mounting screws for attaching the system to the rack Assemble the Brackets and ExtendersTighten the screws and then remove the template Repeat this procedure for the second bracket and extender Six short screws for assembling two brackets and extenders Secure each bolt with a washer Adjust the mounting Mounting Xserve RAID in a Rack Mount the System in the Rack Secure the System in the Rack or Cabinet Moving the Xserve RAID System System and a Network Connecting Xserve RAID to a Host System or Switch Installing the Host Bus Adapter Card in the Host SystemAbout Fibre Channel Connections and Cables Connecting the System to Xserve or a Power Mac G4 Connecting Xserve RAID to a Switch or Hub Removing Cables From the Xserve RAID and Host Systems Connecting to a Network Connecting Power to the System Plug one of the system’s power cords into the UPS Connecting an Uninterruptible Power SupplyFollow these steps to connect a UPS unit to the system Using the Xserve RAID System Starting Up the SystemUsing Status Lights and Other Indicators Turning Off the SystemLight manually check If the System Has a Problem Follow these steps to install or replace a drive module Installing or Replacing an Apple Drive ModuleAbout Replacing Components Security lock Replacing a Power Supply Follow these steps to replace a power supplyReplacing a Cooling Module Installing or Replacing Components Replacing a RAID Controller Module Installing or Replacing a Battery Module Obtaining Additional Replacement Components Installing Xserve RAID Hardware and Software Setting Up the Xserve RAID SystemInstalling the system in a rack or cabinet RAID OverviewScalability for expansion of storage Connecting to an Ethernet networkAbout RAID Storage How RAID WorksData Storage Methods RAID 0+1 requires a minimum of four drives RAID LevelsRAID 5 requires a minimum of three drives RAID 3 requires a minimum of three drivesHardware and Software RAID What’s Next? Tools for Configuring the Xserve RAID System Planning RAID Storage For the Xserve RAID SystemRAID Controllers and Drive Modules Drive modules Controllers RAID RAID 0+1 Xserve RAID SchemesSystem With Four Drive Modules RAID 1 Schemes RAID 3 or RAID 0+1 and RAID 10 Schemes RAID System With Seven Drive ModulesDisk Mirror Mirror Mirror Hot spare RAID 3 or 5 Hot spare RAID 3 or Disk System With 14 Drive Modules RAID 0+1 Disk Hot spare RAID 1 and RAID 3 or Disk Mirrors RAID1 Hot spare RAID RAID 30 and 50 Schemes Storage Capacities for Xserve RAID Schemes Xserve RAID Hardware Connections Connecting a Four-Drive System to a Host Computer or Switch Connecting a 14-Drive System to a Host Computer or SwitchGlossary Common RAID TermsPage Fibre Channel PCI Card Specifications RAID Controller SpecificationsSpecifications Ethernet Specifications Apple Drive Module SpecificationsDimensions and Operating Environment UPS Interface SpecificationsPin D connector Cooling Module Specifications Power Supply SpecificationsBattery Module Optional Information Safety, Maintenance, and Ergonomics Important Safety InformationCleaning Your Equipment Power SupplyHandling Your System Safety, Maintenance, and Ergonomics Page Complies with European Directive 89/336/EEC