Apple NMB-003 manual Complies with European Directive 89/336/EEC

Page 91

Communications Regulation Information

FCC Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio- frequency energy, and if not installed and used in accordance with Apple’s instructions, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her own expense.

Important Changes or modifications to this product not authorized by Apple Computer, Inc., could void the EMC compliance and negate your authority to operate the product.

This product was tested for EMC compliance under conditions that included the use of Apple peripheral devices and Apple shielded cables and connectors between system components. It is important that you use Apple peripheral devices and shielded cables and connectors between system components to reduce the possibility of causing interference to radios, television sets, and other electronic devices. You can obtain Apple peripheral devices and the proper shielded cables and connectors through an Apple-authorized dealer. For non-Apple peripheral devices, contact the manufacturer or dealer for assistance.

Industry Canada Statement

Complies with the Canadian ICES-003 Class A specifications.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

European Union Statement

Complies with European Directive 89/336/EEC.

CISPR 22 & EN55022 Statement

Warning This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.

VCCI Class A Statement

High-Risk Activities Warning

This system is not intended for use in the operation of nuclear facilities, aircraft navigation or communications systems, or air traffic control machines, or for any other uses where the failure of the system could lead to death, personal injury or severe environmental damage.

Communications Regulation Information

91

Image 91
Contents User’s Guide Apple Computer, Inc. All rights reserved Apple Computer, IncContents Installing or Replacing Components Installing the SystemConnecting Xserve RAID to a Host System and a Network Using the Xserve RAID SystemRAID Overview Installing Xserve RAID Hardware and SoftwareConnecting a 14-Drive System to a Host Computer or Switch Data Storage MethodsAppendix B Safety, Maintenance, and Ergonomics Glossary Appendix a SpecificationsAbout This Guide Page Introducing Xserve RAID Unpacking the System Introducing Xserve RAID Your System at a Glance-Front Panel Indicates temperature status green is OK, red is failure RAID Your System at a Glance-Back PanelRedundant, hot-swappable cooling module cools the system Your System at a Glance-Mounting Hardware Use this bar to fasten extenders C and D for a deep rack Page Use your leg muscles to lift Preparing to Install Xserve RAID in a RackGuidelines for Installation Precautions for Handling the SystemChoosing the System’s Location in the Rack Lift with a smooth motion don’t jerk the load up or downRack Stability Electrical PowerSecurity Operating EnvironmentMounting Xserve RAID in a Rack Getting Ready to Install the System Determine the Position for the System in the Rack Prepare the System for Installation Installing the SystemFollow the instructions in Unpacking the System on Assemble the Brackets and Extenders Two mounting screws for attaching the system to the rackTighten the screws and then remove the template Repeat this procedure for the second bracket and extender Six short screws for assembling two brackets and extenders Secure each bolt with a washer Adjust the mounting Mounting Xserve RAID in a Rack Mount the System in the Rack Secure the System in the Rack or Cabinet Moving the Xserve RAID System System and a Network Connecting Xserve RAID to a Host System or Switch Installing the Host Bus Adapter Card in the Host SystemAbout Fibre Channel Connections and Cables Connecting the System to Xserve or a Power Mac G4 Connecting Xserve RAID to a Switch or Hub Removing Cables From the Xserve RAID and Host Systems Connecting to a Network Connecting Power to the System Plug one of the system’s power cords into the UPS Connecting an Uninterruptible Power SupplyFollow these steps to connect a UPS unit to the system Starting Up the System Using the Xserve RAID SystemTurning Off the System Using Status Lights and Other IndicatorsLight manually check If the System Has a Problem Follow these steps to install or replace a drive module Installing or Replacing an Apple Drive ModuleAbout Replacing Components Security lock Follow these steps to replace a power supply Replacing a Power SupplyReplacing a Cooling Module Installing or Replacing Components Replacing a RAID Controller Module Installing or Replacing a Battery Module Obtaining Additional Replacement Components RAID Overview Setting Up the Xserve RAID SystemInstalling the system in a rack or cabinet Installing Xserve RAID Hardware and SoftwareHow RAID Works Connecting to an Ethernet networkAbout RAID Storage Scalability for expansion of storageData Storage Methods RAID Levels RAID 0+1 requires a minimum of four drivesRAID 5 requires a minimum of three drives RAID 3 requires a minimum of three drivesHardware and Software RAID What’s Next? Planning RAID Storage For the Xserve RAID System Tools for Configuring the Xserve RAID SystemRAID Controllers and Drive Modules Drive modules Controllers RAID RAID 0+1 Xserve RAID SchemesSystem With Four Drive Modules RAID 1 Schemes RAID 3 or RAID 0+1 and RAID 10 Schemes System With Seven Drive Modules RAIDDisk Mirror Mirror Mirror Hot spare RAID 3 or 5 Hot spare RAID 3 or Disk System With 14 Drive Modules RAID 0+1 Disk Hot spare RAID 1 and RAID 3 or Disk Mirrors RAID1 Hot spare RAID RAID 30 and 50 Schemes Storage Capacities for Xserve RAID Schemes Xserve RAID Hardware Connections Connecting a 14-Drive System to a Host Computer or Switch Connecting a Four-Drive System to a Host Computer or SwitchCommon RAID Terms GlossaryPage Fibre Channel PCI Card Specifications RAID Controller SpecificationsSpecifications UPS Interface Specifications Apple Drive Module SpecificationsDimensions and Operating Environment Ethernet SpecificationsPin D connector Cooling Module Specifications Power Supply SpecificationsBattery Module Optional Information Important Safety Information Safety, Maintenance, and ErgonomicsCleaning Your Equipment Power SupplyHandling Your System Safety, Maintenance, and Ergonomics Page Complies with European Directive 89/336/EEC