Acnodes RMC 7182 user manual Control Panel, System Cooling

Page 63

RMC 7182

1U Rackmount System

6-2 Control Panel

The control panel (located on the front of the chassis) must be connected to the JF1 connector on the serverboard to provide you with system control buttons and status indicators. These wires have been bundled together in a ribbon cable to simplify the connection.

Connect the cable from JF1 on the serverboard to the Control Panel PCB (printed circuit board). Make sure the red wire plugs into pin 1 on both connectors. Pull all excess cabling out of the airflow path. The LEDs inform you of system status. See Chapter 3 for details on the LEDs and the control panel buttons. Details on JF1 can be found in Chapter 5.

6-3 System Cooling

Four 4-cm counter-rotating fans provide the cooling for the system. Each fan unit is actually made up of two fans joined back-to-back, which rotate in opposite directions. This counter-rotating action gener- ates exceptional airflow and works to dampen vibration levels. The SC113 chassis provides two addi- tional open fan housings, where an additional system fan may be added for optimal cooling.

It is very important that the chassis top cover is properly installed and making a good seal in order for the cooling air to circulate properly through the chassis and cool the components. See Figure 6-2.

	© Copyright 2009 Acnodes, Inc.
661 Brea Canyon Rd., Suite 3	All rights reserved. Product description and product specifications
Walnut, CA 91789	are subject to change without notice. For latest product information,
tel: 909.598.7388, fax: 909.598.0218	please visit Acnodes’ web site at www.acnodes.com.

Image 63

Contents RMC Copyright 2005 Acnodes, Inc Manual Organization PrefaceAdvanced Motherboard Setup Advanced Chassis SetupBios Table of Contents System Interface Installing the System in to a RackAdvanced Motherboard Setup NIC2 JLAN2 LED NIC1 JLAN1 LED Advanced Chassis Setup Bios Overview IntroductionMemory Motherboard FeaturesOther Features ProcessorRMC Control Panel Server Chassis FeaturesSystem Power Sata SubsystemUnpacking the System Choosing a Setup LocationPreparing for Setup OverviewServer Precautions Rack PrecautionsRack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInner Rails Installing the Rack RailsOuter Rails RMC Installing the Chassis into a Rack Installing the Server into a Telco Rack Checking the Motherboard Setup Removing the Chassis Cover FigureChecking the Components Checking the Airflow Checking the Drive Bay SetupProviding Power Checking the DrivesReset Button PowerControl Panel Buttons Universal Information LED Control Panel LEDsNIC2 Drive Carrier LEDs Electrical Safety Precautions System SafetyGeneral Safety Precautions ESD Precautions Operating Precautions Handling the Motherboard PrecautionsServerboard Installation Installing to the ChassisUnpacking Connecting the Control Panel Connecting CablesConnecting Data Cables Connecting Power CablesI/O Ports Installing an LGA1366 Processor Installing the Processor and HeatsinkRMC Installing a Passive CPU Heatsink Removing the Heatsink Installing & Removing DIMMs Installing Memory ModulesMaximum Memory Possible Memory SupportPCI Expansion Cards Installing a PCI Expansion CardServerboard Details RMC Power Button Connector DefinitionsMain ATX Power Supply Connector Processor Power ConnectorHDD LED/UID Switch Power On LEDOverheat/Fan Fail/UID LED Serial Ports NMI ButtonFan Headers ATX PS/2 Keyboard and PS/2 Mouse PortsOverheat/Fan Fail LED Chassis IntrusionWake-On-LAN External Speaker/Internal BuzzerSgpio Headers Onboard Power LEDPower Supply SMBus Connector Universal Serial Bus USBUnit Identifier Button Power Supply Fail LED HeaderAlarm Reset ButtonCmos Clear Jumper SettingsVGA Enable/Disable Explanation of JumpersLAN1/2 Enable/Disable Watch Dog Enable/DisableUSB Wake-Up SMBus to PCI Slots BMC Enable/DisableSAS Enable/Disable SAS RAID Mode SelectIpmi Dedicated LAN LEDs Onboard IndicatorsOnboard Power LED LE1 LAN1/2 LEDsBMC Heartbeat LED SAS Activity LEDSAS Heartbeat LED SAS Ports Floppy ConnectorSata and Floppy Drive Connections Sata PortsDriver/Tool Installation Display Screen Installing SoftwareRMC RMC Tools Required Static-Sensitive DevicesSystem Cooling Control PanelAdding a System Fan System Fan FailureReplacing a System Fan Figure Installing a Hard Drive into a Drive Carrier Figure Drive Bay Installation/RemovalAccessing the Drive Bays Hard Drive InstallationRemoving a Hard Drive Figure DVD Drive Installation Power Supply Failure Power SupplyRemoving/Replacing the Power Supply Starting Bios Setup Utility How To Change the Configuration DataIntroduction Starting the Setup Utility Main SetupSystem Memory System Time/System DateAddOn ROM Display Mode Advanced Setup ConfigurationsXboot Features Quick Boot Quiet BootPS/2 Mouse Support Wait For F1 If ErrorPower Button Function Restore on AC Power LossClock Spread Spectrum Ratio Cmos SettingHardware Prefetcher Available when supported by the CPU XProcessor & Clock Options CPU RatioIntel Eist Technology Active Processor CoresTDC Limit Override Intel Turbo Boost Configuration Turbo Ratio Limit ProgramCore Ratio Limit ~ 3 Core Ratio LimitXAdvanced Chipset Control Memory Frequency Memory ModeTemperature Rise QPI L0s and L1Dimm Pitch High Performance Event TimerAir Flow AltitudeXide / Floppy Configuration IDE Detect Timeout sec LBA/Large ModeType PIO Mode DMA ModeBlock Multi-Sector Transfer 32Bit Data Transfer A.R.T. For Hard disk drivesXPCI/PnP Configuration XRemote Access Configuration XSuper IO Device ConfigurationXHardware Health Configuration CPU Temperature System TemperatureUSB Device WakeUp Xacpi ConfigurationFan Speed Control Modes Fan1 ~ Fan 5 ReadingTPM Enable/Disable Status Headless ModeAcpi Version Features XTrusted Computing TCG/TPM Support Execute TPM CommandXipmi Configuration BMC Watch Dog Timer Action Set PEF ConfigurationMark all events as read XEvent Log ConfigurationBMC WatchDog TimeOut MinSec View Event LogChange Supervisor Password Security SettingsSupervisor Password User PasswordBoot Sector Virus Protection Change User PasswordBoot Settings XBoot Device PriorityXHard Disk Drives Save Changes and Exit Retry Boot DevicesExit Options XRemovable DrivesDiscard Changes Load Optimal DefaultsLoad Fail-Safe Defaults Discard Changes and ExitRecoverable Post Error Beep Codes Appendix a Post Error Beep CodesInstalling Windows on RAID Systems Appendix B Installing the Windows OSInstalling Windows on Non-RAID Systems SAS Controller ProcessorsChipset Memory CapacitySystem Cooling WeightPower Supply Chassis