Acnodes RMC 7182 user manual Installing a Passive CPU Heatsink

Page 40

RMC 7182

1U Rackmount System

Installing a Passive CPU Heatsink

Notes: The motherboard comes with a heatsink bracket pre-in- stalled on the reverse side of the board. Do not apply any thermal grease to the heatsink or the CPU die; the required amount has al-

ready been applied.

1. Place the heatsink on top

of the CPU so that the four mounting holes are aligned with those on the retention mechanism.

2.Install two diagonal screws (i.e. the #1 and the #2

screws) and tighten them until just snug (do not fully tighten the screws to avoid damaging the CPU.)

3.Repeat step 2 with the #3

and #4 screws. Make sure all screws are snug.

	© Copyright 2005 Acnodes, Inc.
661 Brea Canyon Rd., Suite 3	All rights reserved. Product description and product specifications
Walnut, CA 91789	are subject to change without notice. For latest product information,
tel: 909.598.7388, fax: 909.598.0218	please visit Acnodes’ web site at www.acnodes.com.

Image 40

Contents RMC Copyright 2005 Acnodes, Inc Preface Manual OrganizationAdvanced Chassis Setup Advanced Motherboard SetupBios Table of Contents Installing the System in to a Rack System InterfaceAdvanced Motherboard Setup NIC2 JLAN2 LED NIC1 JLAN1 LED Advanced Chassis Setup Bios Introduction OverviewMotherboard Features Other FeaturesProcessor MemoryRMC Server Chassis Features System PowerSata Subsystem Control PanelChoosing a Setup Location Preparing for SetupOverview Unpacking the SystemRack Precautions Server PrecautionsRack Mounting Considerations Installing the System into a Rack Identifying the Sections of the Rack RailsInstalling the Rack Rails Inner RailsOuter Rails RMC Installing the Chassis into a Rack Installing the Server into a Telco Rack Removing the Chassis Cover Figure Checking the Motherboard SetupChecking the Components Checking the Drive Bay Setup Providing PowerChecking the Drives Checking the AirflowPower Reset ButtonControl Panel Buttons Control Panel LEDs Universal Information LEDNIC2 Drive Carrier LEDs System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Precautions Handling the MotherboardInstalling to the Chassis Serverboard InstallationUnpacking Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control PanelI/O Ports Installing the Processor and Heatsink Installing an LGA1366 ProcessorRMC Installing a Passive CPU Heatsink Removing the Heatsink Installing Memory Modules Installing & Removing DIMMsMemory Support Maximum Memory PossibleInstalling a PCI Expansion Card PCI Expansion CardsServerboard Details RMC Connector Definitions Main ATX Power Supply ConnectorProcessor Power Connector Power ButtonPower On LED HDD LED/UID SwitchOverheat/Fan Fail/UID LED NMI Button Fan HeadersATX PS/2 Keyboard and PS/2 Mouse Ports Serial PortsChassis Intrusion Wake-On-LANExternal Speaker/Internal Buzzer Overheat/Fan Fail LEDOnboard Power LED Power Supply SMBus ConnectorUniversal Serial Bus USB Sgpio HeadersPower Supply Fail LED Header Alarm ResetButton Unit Identifier ButtonJumper Settings VGA Enable/DisableExplanation of Jumpers Cmos ClearWatch Dog Enable/Disable LAN1/2 Enable/DisableUSB Wake-Up BMC Enable/Disable SAS Enable/DisableSAS RAID Mode Select SMBus to PCI SlotsOnboard Indicators Onboard Power LED LE1LAN1/2 LEDs Ipmi Dedicated LAN LEDsSAS Activity LED BMC Heartbeat LEDSAS Heartbeat LED Floppy Connector Sata and Floppy Drive ConnectionsSata Ports SAS PortsInstalling Software Driver/Tool Installation Display ScreenRMC RMC Static-Sensitive Devices Tools RequiredControl Panel System CoolingSystem Fan Failure Adding a System FanReplacing a System Fan Figure Drive Bay Installation/Removal Accessing the Drive BaysHard Drive Installation Installing a Hard Drive into a Drive Carrier FigureRemoving a Hard Drive Figure DVD Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply How To Change the Configuration Data Starting Bios Setup UtilityIntroduction Main Setup Starting the Setup UtilitySystem Time/System Date System MemoryAdvanced Setup Configurations Xboot Features Quick BootQuiet Boot AddOn ROM Display ModeWait For F1 If Error Power Button FunctionRestore on AC Power Loss PS/2 Mouse SupportRatio Cmos Setting Hardware Prefetcher Available when supported by the CPUXProcessor & Clock Options CPU Ratio Clock Spread SpectrumActive Processor Cores Intel Eist TechnologyIntel Turbo Boost Configuration Turbo Ratio Limit Program Core Ratio Limit~ 3 Core Ratio Limit TDC Limit OverrideXAdvanced Chipset Control Memory Mode Temperature RiseQPI L0s and L1 Memory FrequencyHigh Performance Event Timer Air FlowAltitude Dimm PitchXide / Floppy Configuration LBA/Large Mode IDE Detect Timeout secType DMA Mode PIO ModeBlock Multi-Sector Transfer A.R.T. For Hard disk drives 32Bit Data TransferXPCI/PnP Configuration XSuper IO Device Configuration XRemote Access ConfigurationXHardware Health Configuration System Temperature CPU TemperatureXacpi Configuration Fan Speed Control ModesFan1 ~ Fan 5 Reading USB Device WakeUpHeadless Mode Acpi Version Features XTrusted Computing TCG/TPM SupportExecute TPM Command TPM Enable/Disable StatusXipmi Configuration Set PEF Configuration BMC Watch Dog Timer ActionXEvent Log Configuration BMC WatchDog TimeOut MinSecView Event Log Mark all events as readSecurity Settings Supervisor PasswordUser Password Change Supervisor PasswordChange User Password Boot Sector Virus ProtectionXBoot Device Priority Boot SettingsXHard Disk Drives Retry Boot Devices Exit OptionsXRemovable Drives Save Changes and ExitLoad Optimal Defaults Load Fail-Safe DefaultsDiscard Changes and Exit Discard ChangesAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesAppendix B Installing the Windows OS Installing Windows on RAID SystemsInstalling Windows on Non-RAID Systems Processors ChipsetMemory Capacity SAS ControllerWeight Power SupplyChassis System Cooling