Advantech MIC-3318 manual Display, Mechanical and Environmental Specifications

Page 12

USB port: Two USB ports with fuse protection comply with USB specification 2.0/1.1

PCI-to-PCI Bridge: One PERICOM PI7C8150 controller chip, drives up to seven bus master peripherals.

Watchdog Timer: It provides system reset, software control. Time interval is programmable from 1 to 255 seconds/minutes.

Ethernet LAN:10/100/1000Base-TX Ethernet Interface

Controller Chips: Two Intel® 82540EM Gigabit Ethernet controller chips provides Dual Gigabit ports, two front RJ-45 Gigabit LAN port 10 Mbps, 100 Mbps and 1000Mbps auto-switching

PICMG 2.1 CompactPCI Hot Swap Specification R1.0 Compliant

1.2.2 Display

•Interface: Intel® Extreme Graphics Architecture

Controller: Intel 845GV chipset integrated

•Display memory: shared from system memory up to 8-64MB SDRAM

Bus Interface: PCI 2.2 compliant, 32bit/33 MHz

1.2.3 Mechanical and Environmental Specifications

Board Size: 160 x 100 mm (3U size), 2-slot (8TE) wide.

Max. power Requirements: CPU 1.7 GHz

+5 V (4.75 ~ 5.25 V) @ 5.6A

+3.3 V (4.75 ~ 5.25 V) @ 1.8A

+12 V (4.75 ~ 5.25 V) @ 16mA

• Operating Temperature:

-10 ~ 50° C (14 ~122° F) CPU Run at 1.7 GHz

-10 ~ 60° C (14 ~140° F) CPU Run at 1.2 GHz

4 MIC-3318 User's Manual

Image 12
Contents MIC-3318 CE Notification Product Warranty Packing List Contents Software Configuration Programming the Watchdog Timer Figures Hardware Configuration Introduction High Performance Intel Pentium 4 Processor-MSpecifications Standard SBC functionsMechanical and Environmental Specifications DisplayFunction Block Diagram MIC-3318 function block diagramBoard Dimensions MIC-3318 board dimensionsJumper Settings Assembling / Disassembling MIC-3318Jumper Locations Number FunctionJumper Settings Open ClosedCompactFlash master/slave selection1F-JP5, pin 1,2 Clear Cmos JP1, pin 2,4,6Serial Ports COM1 and COM2 Mode RS-232/ 422/485 Connectors HDD LEDMIC-3318 connector locations 1F Front Panel Connectors and Indicators Safety PrecautionsInstalling Sdram SODIMMs Page Connecting Peripherals VGA Display Connector 1F-CN7 IDE Device 2F-CN8, CN9CompactFlash Interface 1F-CN2 PS/2 Keyboard and Mouse Conn F-CN1Ethernet Configuration 2F-RJ1, RJ2 USB Connector 1F-CN15, CN16Serial Ports 2F-CN3, CN5, CN4, CN6 Card Installation Install a card by forcing it into the chassisInstalling/removing the MIC-3318 into/from the chassis Page Software Configuration Overview Intel Chipset Software Installation Utility Utilities and DriversIDE Drivers Intel Application Accelerator USB Drivers /Utility Watchdog Timer WDT Driver Installing the Driver for the MIC-3318 Watchdog TimerUSB driver Software Configuration Page Software Configuration How to Use the MIC-3318 Watchdog Timer Software Configuration Page Award Bios Setup Initial screen of the setup program Entering Setup Standard Cmos SetupAdvanced Bios Features Setup Advanced Bios features setup screenCPU L1 & L2 Cache Default value is On Default is Enabled Advanced Chipset Features Setup Advanced Chipset Features setup screenUser can select 3 options DDR200, DDR266, Auto Default System Bios Cacheable Integrated Peripherals setup screens Integrated PeripheralsOn-Chip Primary/Secondary PCI IDE Init Display First Power Management Setup Parallel Port Mode6 PNP/PCI Configuration Setup PNP/PCI configuration screenReset Configuration Data Load Optimized Defaults PC Health StatusSet Password Save & Exit SetupExit Without Saving Programming the Watchdog Timer Programming the Watchdog Timer Figure A-1 Procedure of programming the watchdog timerAddress Register 2E Attribute Description Enable watchdog timer and set 10 sec. as timeout interval Example ProgramsAppendix a Programming the Watchdog Timer Page Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by mouse Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by keyboard Appendix a Programming the Watchdog Timer Page Pin Assignments PS/2 Keyboard and Mouse Port 1F-CN1 GND PDD3 PDD11 PDD4 DB-15 VGA Port 1F-CN7 USB 1.1/2.0 Ports 1F-CN15 and 1F-CN16 COMport 2F-CN3, 2F-CN5, 2F-CN4,2F- CN6 Parallel Port 2F-CN7,2F-CN8 For front panel 2F-CN7Secondary IDE Connector for 2.5 HDD 2F-CN9, 2F-CN17 For direct installation 2F-CN9 For wiring out 2F-CN17IRQ15 SDA1 S66DET SDA0 SDA2 SDCS#1 SDCS#3 Hddled GND Gigabit LAN Port 2F-RJ1,2F-RJ2