Advantech MIC-3318 manual USB 1.1/2.0 Ports 1F-CN15 and 1F-CN16

Page 77

B.4 USB 1.1/2.0 Ports (1F-CN15 AND 1F-CN16)

4

3

2

1

Table B-4: USB 1.1/2.0 ports pin definitions

Pin Signal

1+5V

2USB_P-

3USB_P+

4GND

Appendix B Pin Assignments

69

Image 77

Contents MIC-3318 CE Notification Product Warranty Packing List Contents Software Configuration Programming the Watchdog Timer Figures Hardware Configuration High Performance Intel Pentium 4 Processor-M IntroductionStandard SBC functions SpecificationsDisplay Mechanical and Environmental SpecificationsMIC-3318 function block diagram Function Block DiagramMIC-3318 board dimensions Board DimensionsAssembling / Disassembling MIC-3318 Jumper SettingsNumber Function Jumper LocationsOpen Closed Jumper SettingsClear Cmos JP1, pin 2,4,6 CompactFlash master/slave selection1F-JP5, pin 1,2Serial Ports COM1 and COM2 Mode RS-232/ 422/485 HDD LED ConnectorsMIC-3318 connector locations 1F Safety Precautions Front Panel Connectors and IndicatorsInstalling Sdram SODIMMs Page Connecting Peripherals IDE Device 2F-CN8, CN9 VGA Display Connector 1F-CN7CompactFlash Interface 1F-CN2 PS/2 Keyboard and Mouse Conn F-CN1Serial Ports 2F-CN3, CN5, CN4, CN6 Ethernet Configuration 2F-RJ1, RJ2USB Connector 1F-CN15, CN16 Install a card by forcing it into the chassis Card InstallationInstalling/removing the MIC-3318 into/from the chassis Page Software Configuration Overview Utilities and Drivers Intel Chipset Software Installation UtilityIDE Drivers Intel Application Accelerator USB Drivers /Utility USB driver Watchdog Timer WDT DriverInstalling the Driver for the MIC-3318 Watchdog Timer Software Configuration Page Software Configuration How to Use the MIC-3318 Watchdog Timer Software Configuration Page Award Bios Setup Initial screen of the setup program Standard Cmos Setup Entering SetupAdvanced Bios features setup screen Advanced Bios Features SetupCPU L1 & L2 Cache Default value is On Default is Enabled Advanced Chipset Features setup screen Advanced Chipset Features SetupUser can select 3 options DDR200, DDR266, Auto Default System Bios Cacheable Integrated Peripherals Integrated Peripherals setup screensOn-Chip Primary/Secondary PCI IDE Init Display First Parallel Port Mode Power Management SetupPNP/PCI configuration screen 6 PNP/PCI Configuration SetupReset Configuration Data PC Health Status Load Optimized DefaultsExit Without Saving Set PasswordSave & Exit Setup Programming the Watchdog Timer Figure A-1 Procedure of programming the watchdog timer Programming the Watchdog TimerAddress Register 2E Attribute Description Example Programs Enable watchdog timer and set 10 sec. as timeout intervalAppendix a Programming the Watchdog Timer Page Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by mouse Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by keyboard Appendix a Programming the Watchdog Timer Page Pin Assignments PS/2 Keyboard and Mouse Port 1F-CN1 GND PDD3 PDD11 PDD4 DB-15 VGA Port 1F-CN7 USB 1.1/2.0 Ports 1F-CN15 and 1F-CN16 COMport 2F-CN3, 2F-CN5, 2F-CN4,2F- CN6 For front panel 2F-CN7 Parallel Port 2F-CN7,2F-CN8For direct installation 2F-CN9 For wiring out 2F-CN17 Secondary IDE Connector for 2.5 HDD 2F-CN9, 2F-CN17IRQ15 SDA1 S66DET SDA0 SDA2 SDCS#1 SDCS#3 Hddled GND Gigabit LAN Port 2F-RJ1,2F-RJ2