Advantech MIC-3318 manual Packing List

Page 4

Packing List

Before installing your board, ensure that the following materials have been received:

•One MIC-3318 all-in-one single board computer

•One utility CD-ROM

•Two serial port cables

•One 6-pin mini-DIN to PS/2 keyboard and PS/2 mouse cable

•One hard disk drive (IDE) interface cable (44-pin)

•One warranty certificate

•This user’s manual

If any of these items are missing or damaged, contact your distributor or sales representative immediately.

Technical Support and Sales Assistance

If you have any technical questions about the MIC-3318 or any other Advantech products, please visit our support website at:

•http://www.advantech.com.tw/support

For more information about Advantech’s products and sales information, please visit:

•http://www.advantech.com

iv

Image 4

Contents MIC-3318 CE Notification Product Warranty Packing List Contents Software Configuration Programming the Watchdog Timer Figures Hardware Configuration Introduction High Performance Intel Pentium 4 Processor-MSpecifications Standard SBC functionsMechanical and Environmental Specifications DisplayFunction Block Diagram MIC-3318 function block diagramBoard Dimensions MIC-3318 board dimensionsJumper Settings Assembling / Disassembling MIC-3318Jumper Locations Number FunctionJumper Settings Open ClosedCompactFlash master/slave selection1F-JP5, pin 1,2 Clear Cmos JP1, pin 2,4,6Serial Ports COM1 and COM2 Mode RS-232/ 422/485 Connectors HDD LEDMIC-3318 connector locations 1F Front Panel Connectors and Indicators Safety PrecautionsInstalling Sdram SODIMMs Page Connecting Peripherals VGA Display Connector 1F-CN7 IDE Device 2F-CN8, CN9CompactFlash Interface 1F-CN2 PS/2 Keyboard and Mouse Conn F-CN1USB Connector 1F-CN15, CN16 Ethernet Configuration 2F-RJ1, RJ2Serial Ports 2F-CN3, CN5, CN4, CN6 Card Installation Install a card by forcing it into the chassisInstalling/removing the MIC-3318 into/from the chassis Page Software Configuration Overview Intel Chipset Software Installation Utility Utilities and DriversIDE Drivers Intel Application Accelerator USB Drivers /Utility Installing the Driver for the MIC-3318 Watchdog Timer Watchdog Timer WDT DriverUSB driver Software Configuration Page Software Configuration How to Use the MIC-3318 Watchdog Timer Software Configuration Page Award Bios Setup Initial screen of the setup program Entering Setup Standard Cmos SetupAdvanced Bios Features Setup Advanced Bios features setup screenCPU L1 & L2 Cache Default value is On Default is Enabled Advanced Chipset Features Setup Advanced Chipset Features setup screenUser can select 3 options DDR200, DDR266, Auto Default System Bios Cacheable Integrated Peripherals setup screens Integrated PeripheralsOn-Chip Primary/Secondary PCI IDE Init Display First Power Management Setup Parallel Port Mode6 PNP/PCI Configuration Setup PNP/PCI configuration screenReset Configuration Data Load Optimized Defaults PC Health StatusSave & Exit Setup Set PasswordExit Without Saving Programming the Watchdog Timer Programming the Watchdog Timer Figure A-1 Procedure of programming the watchdog timerAddress Register 2E Attribute Description Enable watchdog timer and set 10 sec. as timeout interval Example ProgramsAppendix a Programming the Watchdog Timer Page Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by mouse Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by keyboard Appendix a Programming the Watchdog Timer Page Pin Assignments PS/2 Keyboard and Mouse Port 1F-CN1 GND PDD3 PDD11 PDD4 DB-15 VGA Port 1F-CN7 USB 1.1/2.0 Ports 1F-CN15 and 1F-CN16 COMport 2F-CN3, 2F-CN5, 2F-CN4,2F- CN6 Parallel Port 2F-CN7,2F-CN8 For front panel 2F-CN7Secondary IDE Connector for 2.5 HDD 2F-CN9, 2F-CN17 For direct installation 2F-CN9 For wiring out 2F-CN17IRQ15 SDA1 S66DET SDA0 SDA2 SDCS#1 SDCS#3 Hddled GND Gigabit LAN Port 2F-RJ1,2F-RJ2