Advantech MIC-3318 manual Software Configuration

Page 41

Step 5. Click Enable to enable the setting.

Step 6. Check the Start watchdog service on boot to enable the Watchdog timer to start automatically after the system boots every time.

Step 7. Click OK, then the configuration procedure is finished.

Chapter 3 Software Configuration

3 3

Image 41

Contents MIC-3318 CE Notification Product Warranty Packing List Contents Software Configuration Programming the Watchdog Timer Figures Hardware Configuration High Performance Intel Pentium 4 Processor-M IntroductionStandard SBC functions SpecificationsDisplay Mechanical and Environmental SpecificationsMIC-3318 function block diagram Function Block DiagramMIC-3318 board dimensions Board DimensionsAssembling / Disassembling MIC-3318 Jumper SettingsNumber Function Jumper LocationsOpen Closed Jumper SettingsClear Cmos JP1, pin 2,4,6 CompactFlash master/slave selection1F-JP5, pin 1,2Serial Ports COM1 and COM2 Mode RS-232/ 422/485 HDD LED ConnectorsMIC-3318 connector locations 1F Safety Precautions Front Panel Connectors and IndicatorsInstalling Sdram SODIMMs Page Connecting Peripherals IDE Device 2F-CN8, CN9 VGA Display Connector 1F-CN7CompactFlash Interface 1F-CN2 PS/2 Keyboard and Mouse Conn F-CN1Serial Ports 2F-CN3, CN5, CN4, CN6 Ethernet Configuration 2F-RJ1, RJ2USB Connector 1F-CN15, CN16 Install a card by forcing it into the chassis Card InstallationInstalling/removing the MIC-3318 into/from the chassis Page Software Configuration Overview Utilities and Drivers Intel Chipset Software Installation UtilityIDE Drivers Intel Application Accelerator USB Drivers /Utility USB driver Watchdog Timer WDT DriverInstalling the Driver for the MIC-3318 Watchdog Timer Software Configuration Page Software Configuration How to Use the MIC-3318 Watchdog Timer Software Configuration Page Award Bios Setup Initial screen of the setup program Standard Cmos Setup Entering SetupAdvanced Bios features setup screen Advanced Bios Features SetupCPU L1 & L2 Cache Default value is On Default is Enabled Advanced Chipset Features setup screen Advanced Chipset Features SetupUser can select 3 options DDR200, DDR266, Auto Default System Bios Cacheable Integrated Peripherals Integrated Peripherals setup screensOn-Chip Primary/Secondary PCI IDE Init Display First Parallel Port Mode Power Management SetupPNP/PCI configuration screen 6 PNP/PCI Configuration SetupReset Configuration Data PC Health Status Load Optimized DefaultsExit Without Saving Set PasswordSave & Exit Setup Programming the Watchdog Timer Figure A-1 Procedure of programming the watchdog timer Programming the Watchdog TimerAddress Register 2E Attribute Description Example Programs Enable watchdog timer and set 10 sec. as timeout intervalAppendix a Programming the Watchdog Timer Page Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by mouse Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by keyboard Appendix a Programming the Watchdog Timer Page Pin Assignments PS/2 Keyboard and Mouse Port 1F-CN1 GND PDD3 PDD11 PDD4 DB-15 VGA Port 1F-CN7 USB 1.1/2.0 Ports 1F-CN15 and 1F-CN16 COMport 2F-CN3, 2F-CN5, 2F-CN4,2F- CN6 For front panel 2F-CN7 Parallel Port 2F-CN7,2F-CN8For direct installation 2F-CN9 For wiring out 2F-CN17 Secondary IDE Connector for 2.5 HDD 2F-CN9, 2F-CN17IRQ15 SDA1 S66DET SDA0 SDA2 SDCS#1 SDCS#3 Hddled GND Gigabit LAN Port 2F-RJ1,2F-RJ2