Advantech MIC-3318 manual Connectors, Hdd Led

Page 20

1.6 Connectors

Onboard connectors link to external devices such as hard disk drives, or keyboards, etc. Table 1-5 lists the function of each connector, and Figure 1-6 and Figure 1-7 illustrate the location of each connector.

Table 1-5: MIC-3318 connector descriptions

Number	Function
1F-CN1	PS/2 keyboard and mouse connector
1F-CN2	Primary IDE CompactFlash Socket
1F-CN7	DB-15 VGA connector
1F-CN15	USB1 1.1/2.0 connector
1F-CN16	USB2 1.1/2.0 connector
1F-J1/J2	Primary CompactPCI bus (32-bit, 33MHz)
1F-SW1	RESET Switch
1F-D9	POWER LED
1F-D10	HDD LED
1F-DIMM1SODIMM 200-pin socket for DDR
2F-CN3	Serial port: COM2
2F-CN4	Serial port: COM2 External Connector to 3F
2F-CN5	Serial port: COM1
2F-CN6	Serial port: COM1 External Connector to 3F
2F-CN7	Parallel port
2F-CN8	Parallel port External Connector to 3F
2F-CN9	Secondary IDE connector for 2.5" HDD
2F-CN17	Secondary IDE connector
2F-RJ1	10/100/1000Base-T Ethernet connector 1
2F-RJ2	10/100/1000Base-T Ethernet connector 2

Please refer to Appendix B for pin assignments.

1 2 MIC-3318 User's Manual

Image 20

Contents MIC-3318 CE Notification Product Warranty Packing List Contents Software Configuration Programming the Watchdog Timer Figures Hardware Configuration Introduction High Performance Intel Pentium 4 Processor-MSpecifications Standard SBC functionsMechanical and Environmental Specifications DisplayFunction Block Diagram MIC-3318 function block diagramBoard Dimensions MIC-3318 board dimensionsJumper Settings Assembling / Disassembling MIC-3318Jumper Locations Number FunctionJumper Settings Open ClosedCompactFlash master/slave selection1F-JP5, pin 1,2 Clear Cmos JP1, pin 2,4,6Serial Ports COM1 and COM2 Mode RS-232/ 422/485 Connectors HDD LEDMIC-3318 connector locations 1F Front Panel Connectors and Indicators Safety PrecautionsInstalling Sdram SODIMMs Page Connecting Peripherals VGA Display Connector 1F-CN7 IDE Device 2F-CN8, CN9CompactFlash Interface 1F-CN2 PS/2 Keyboard and Mouse Conn F-CN1Serial Ports 2F-CN3, CN5, CN4, CN6 Ethernet Configuration 2F-RJ1, RJ2USB Connector 1F-CN15, CN16 Card Installation Install a card by forcing it into the chassisInstalling/removing the MIC-3318 into/from the chassis Page Software Configuration Overview Intel Chipset Software Installation Utility Utilities and DriversIDE Drivers Intel Application Accelerator USB Drivers /Utility USB driver Watchdog Timer WDT DriverInstalling the Driver for the MIC-3318 Watchdog Timer Software Configuration Page Software Configuration How to Use the MIC-3318 Watchdog Timer Software Configuration Page Award Bios Setup Initial screen of the setup program Entering Setup Standard Cmos SetupAdvanced Bios Features Setup Advanced Bios features setup screenCPU L1 & L2 Cache Default value is On Default is Enabled Advanced Chipset Features Setup Advanced Chipset Features setup screenUser can select 3 options DDR200, DDR266, Auto Default System Bios Cacheable Integrated Peripherals setup screens Integrated PeripheralsOn-Chip Primary/Secondary PCI IDE Init Display First Power Management Setup Parallel Port Mode6 PNP/PCI Configuration Setup PNP/PCI configuration screenReset Configuration Data Load Optimized Defaults PC Health StatusExit Without Saving Set PasswordSave & Exit Setup Programming the Watchdog Timer Programming the Watchdog Timer Figure A-1 Procedure of programming the watchdog timerAddress Register 2E Attribute Description Enable watchdog timer and set 10 sec. as timeout interval Example ProgramsAppendix a Programming the Watchdog Timer Page Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by mouse Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by keyboard Appendix a Programming the Watchdog Timer Page Pin Assignments PS/2 Keyboard and Mouse Port 1F-CN1 GND PDD3 PDD11 PDD4 DB-15 VGA Port 1F-CN7 USB 1.1/2.0 Ports 1F-CN15 and 1F-CN16 COMport 2F-CN3, 2F-CN5, 2F-CN4,2F- CN6 Parallel Port 2F-CN7,2F-CN8 For front panel 2F-CN7Secondary IDE Connector for 2.5 HDD 2F-CN9, 2F-CN17 For direct installation 2F-CN9 For wiring out 2F-CN17IRQ15 SDA1 S66DET SDA0 SDA2 SDCS#1 SDCS#3 Hddled GND Gigabit LAN Port 2F-RJ1,2F-RJ2