Advantech How to Install Intel Watchdog Timer Driver for Reliable Performance

Page 36

3.3 USB driver

If the manufacturer/vendor of a USB device recommends downloading an Intel USB driver update as part of troubleshooting your USB device, please contact Microsoft for USB driver support. Intel manu- factures the host controller but the driver is from Microsoft. While you install the Intel INF driver, it will not install the USB driver. Please go to "device manager" to update the USB driver via the Advantech CD utility or via Microsoft’s website.

Note: There are no separate USB (version 1.1 and earlier) drivers available to download for Intel chipsets.

3.4 Watchdog Timer (WDT) Driver

In order to ensure reliable and fail-safe performance, MIC-3318 has a built-in Watchdog Timer to take care of unexpected system failures. Advantech provides the drivers and a utility to activate and configure the timer for Windows2000/XP operating systems. The following is a brief introduction, using Windows2000 as an example, for the installa- tion and configuration procedures.

3.4.1Installing the Driver for the MIC-3318 Watchdog Timer

Step 1. Insert the companion CD-ROM into your CD-ROM drive. Open the directory:\Driver\WDT\8362x\W2K_XP.

2 8 MIC-3318 User's Manual

Image 36
Contents MIC-3318 CE Notification Product Warranty Packing List Contents Software Configuration Programming the Watchdog Timer Figures Hardware Configuration Introduction High Performance Intel Pentium 4 Processor-MSpecifications Standard SBC functionsMechanical and Environmental Specifications DisplayFunction Block Diagram MIC-3318 function block diagramBoard Dimensions MIC-3318 board dimensionsJumper Settings Assembling / Disassembling MIC-3318Jumper Locations Number FunctionJumper Settings Open ClosedCompactFlash master/slave selection1F-JP5, pin 1,2 Clear Cmos JP1, pin 2,4,6Serial Ports COM1 and COM2 Mode RS-232/ 422/485 Connectors HDD LEDMIC-3318 connector locations 1F Front Panel Connectors and Indicators Safety PrecautionsInstalling Sdram SODIMMs Page Connecting Peripherals VGA Display Connector 1F-CN7 IDE Device 2F-CN8, CN9CompactFlash Interface 1F-CN2 PS/2 Keyboard and Mouse Conn F-CN1Ethernet Configuration 2F-RJ1, RJ2 USB Connector 1F-CN15, CN16Serial Ports 2F-CN3, CN5, CN4, CN6 Card Installation Install a card by forcing it into the chassisInstalling/removing the MIC-3318 into/from the chassis Page Software Configuration Overview Intel Chipset Software Installation Utility Utilities and DriversIDE Drivers Intel Application Accelerator USB Drivers /Utility Watchdog Timer WDT Driver Installing the Driver for the MIC-3318 Watchdog TimerUSB driver Software Configuration Page Software Configuration How to Use the MIC-3318 Watchdog Timer Software Configuration Page Award Bios Setup Initial screen of the setup program Entering Setup Standard Cmos SetupAdvanced Bios Features Setup Advanced Bios features setup screenCPU L1 & L2 Cache Default value is On Default is Enabled Advanced Chipset Features Setup Advanced Chipset Features setup screenUser can select 3 options DDR200, DDR266, Auto Default System Bios Cacheable Integrated Peripherals setup screens Integrated PeripheralsOn-Chip Primary/Secondary PCI IDE Init Display First Power Management Setup Parallel Port Mode6 PNP/PCI Configuration Setup PNP/PCI configuration screenReset Configuration Data Load Optimized Defaults PC Health StatusSet Password Save & Exit SetupExit Without Saving Programming the Watchdog Timer Programming the Watchdog Timer Figure A-1 Procedure of programming the watchdog timerAddress Register 2E Attribute Description Enable watchdog timer and set 10 sec. as timeout interval Example ProgramsAppendix a Programming the Watchdog Timer Page Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by mouse Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by keyboard Appendix a Programming the Watchdog Timer Page Pin Assignments PS/2 Keyboard and Mouse Port 1F-CN1 GND PDD3 PDD11 PDD4 DB-15 VGA Port 1F-CN7 USB 1.1/2.0 Ports 1F-CN15 and 1F-CN16 COMport 2F-CN3, 2F-CN5, 2F-CN4,2F- CN6 Parallel Port 2F-CN7,2F-CN8 For front panel 2F-CN7Secondary IDE Connector for 2.5 HDD 2F-CN9, 2F-CN17 For direct installation 2F-CN9 For wiring out 2F-CN17IRQ15 SDA1 S66DET SDA0 SDA2 SDCS#1 SDCS#3 Hddled GND Gigabit LAN Port 2F-RJ1,2F-RJ2