Advantech MIC-3318 manual CPU L1 & L2 Cache

Page 47

Virus Warning

During and after the system boots up, any attempt to write to the boot sector or partition table of the hard disk drive will halt the system. If this happens, a warning message will be displayed. You can run the anti-virus program to locate the problem. If the Virus Warning is disabled, no warning message will appear if anything attempts to access the boot sector or hard disk partition.

CPU L1 & L2 Cache

Enabled (default)	Enable cache
Disabled	Disable cache

Note: The internal cache is built into the processor.

Quick Power On Self Test

This category speeds up Power On Self Test (POST) after you power on the computer. If this is set to Enabled, BIOS will shorten or skip some check items during POST.

Enabled (default) Enable quick POST

Disabled Normal POST

Chapter 4 Award BIOS Setup

39

Image 47

Contents MIC-3318 CE Notification Product Warranty Packing List Contents Software Configuration Programming the Watchdog Timer Figures Hardware Configuration High Performance Intel Pentium 4 Processor-M IntroductionStandard SBC functions SpecificationsDisplay Mechanical and Environmental SpecificationsMIC-3318 function block diagram Function Block DiagramMIC-3318 board dimensions Board DimensionsAssembling / Disassembling MIC-3318 Jumper SettingsNumber Function Jumper LocationsOpen Closed Jumper SettingsClear Cmos JP1, pin 2,4,6 CompactFlash master/slave selection1F-JP5, pin 1,2Serial Ports COM1 and COM2 Mode RS-232/ 422/485 HDD LED ConnectorsMIC-3318 connector locations 1F Safety Precautions Front Panel Connectors and IndicatorsInstalling Sdram SODIMMs Page Connecting Peripherals PS/2 Keyboard and Mouse Conn F-CN1 VGA Display Connector 1F-CN7IDE Device 2F-CN8, CN9 CompactFlash Interface 1F-CN2Serial Ports 2F-CN3, CN5, CN4, CN6 Ethernet Configuration 2F-RJ1, RJ2USB Connector 1F-CN15, CN16 Install a card by forcing it into the chassis Card InstallationInstalling/removing the MIC-3318 into/from the chassis Page Software Configuration Overview Utilities and Drivers Intel Chipset Software Installation UtilityIDE Drivers Intel Application Accelerator USB Drivers /Utility USB driver Watchdog Timer WDT DriverInstalling the Driver for the MIC-3318 Watchdog Timer Software Configuration Page Software Configuration How to Use the MIC-3318 Watchdog Timer Software Configuration Page Award Bios Setup Initial screen of the setup program Standard Cmos Setup Entering SetupAdvanced Bios features setup screen Advanced Bios Features SetupCPU L1 & L2 Cache Default value is On Default is Enabled Advanced Chipset Features setup screen Advanced Chipset Features SetupUser can select 3 options DDR200, DDR266, Auto Default System Bios Cacheable Integrated Peripherals Integrated Peripherals setup screensOn-Chip Primary/Secondary PCI IDE Init Display First Parallel Port Mode Power Management SetupPNP/PCI configuration screen 6 PNP/PCI Configuration SetupReset Configuration Data PC Health Status Load Optimized DefaultsExit Without Saving Set PasswordSave & Exit Setup Programming the Watchdog Timer Figure A-1 Procedure of programming the watchdog timer Programming the Watchdog TimerAddress Register 2E Attribute Description Example Programs Enable watchdog timer and set 10 sec. as timeout intervalAppendix a Programming the Watchdog Timer Page Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by mouse Appendix a Programming the Watchdog Timer Enable watchdog timer to be reset by keyboard Appendix a Programming the Watchdog Timer Page Pin Assignments PS/2 Keyboard and Mouse Port 1F-CN1 GND PDD3 PDD11 PDD4 DB-15 VGA Port 1F-CN7 USB 1.1/2.0 Ports 1F-CN15 and 1F-CN16 COMport 2F-CN3, 2F-CN5, 2F-CN4,2F- CN6 For front panel 2F-CN7 Parallel Port 2F-CN7,2F-CN8For direct installation 2F-CN9 For wiring out 2F-CN17 Secondary IDE Connector for 2.5 HDD 2F-CN9, 2F-CN17IRQ15 SDA1 S66DET SDA0 SDA2 SDCS#1 SDCS#3 Hddled GND Gigabit LAN Port 2F-RJ1,2F-RJ2