Multi-Tech Systems MVP 800 manual Specifications, Ethernet Port, Command Port, Electrical/Physical

Page 13

Chapter 1 - Introduction and Description

Specifications

•Two 1 Meg by 32 byte at 70 nanosecond SIMM is 8 Mb DRAM Caution: SIMM speed and size cannot be mixed

•Two Meg of flash memory

Ethernet Port

•Single Ethernet Interface - 10BASE-T (twisted pair) keyed RJ-45 connector.

Command Port

•Single 19.2K bps asynchronous Command Port with a DB-25 female connector

Voice/Fax Channel

•Two RJ-11 jacks (FXO and FXS)

•One RJ-45 jack (E&M)

Electrical/Physical

•Voltage - 115 VAC (Standard), 240 Volts AC (Optional)

•Frequency - 47 to 63 Hz

•Power Consumption - 18 Watts

•Dimensions - 3.75" high x 17.4" wide x 8" deep

8.9cm high x 44.2cm wide x 20.3cm deep

•Weight - 7.4 pounds (3.4 kg)

13

Image 13

Contents User Guide Record of Revisions RevisionDescription User GuideContents Glossary Index Introduction and Description Preview of this Guide IntroductionWarranty, Service and Tech Support Remote Configuration and ManagementAppendixes Sales Office MultiVOIP ApplicationPhone Directory Data Base Voip Dialing Directory Ethernet Front Panel DescriptionCommand Port Connector Power Connector10Base-T Ethernet Connector Back Panel DescriptionCommand Port SpecificationsEthernet Port Electrical/PhysicalInstallation Safety Warning Telecom Installing Your MultiVOIPConfigure and Install your Host MultiVOIP Configure your Client MultiVOIPsUnpacking Your MultiVOIP Safety WarningsValid Voip Network Connections Cable Connections Cabling ProcedureE&M Jumper Block Jumper Block Positioning ProcedureSoftware Loading and Configuration Configuring Your Host MultiVOIP Software Loading and Configuration IP Protocol Default Setup dialog box displays Software Loading and Configuration Software Loading and Configuration Software Loading and Configuration Software Loading and Configuration Software Loading and Configuration Software Loading and Configuration Configuring Your Client MultiVOIPs Page Software Loading and Configuration Software Loading and Configuration Software Loading and Configuration Software Loading and Configuration Deploy the Voip Network Voip AdministratorSoftware Loading and Configuration MultiVOIP Software Before You Begin MultiVOIP Configuration Interface Tab Changing Channel ParametersFXS Interface Interface FXO InterfaceFXO Disconnect On Voice/Fax Tab MultiVOIP Software Regional Tab Changing the Phone Directory Database MultiVOIP Software Changing IP Parameters Proxy SetupMultiVOIP Software IP Statistics Viewing StatisticsSnmp Statistics Others Setup Viewing Call Progress Viewing Log Entry Details Viewing LogsViewing Channel Totals Reports Remote Configuration and Management Modem-Based Remote ConfigurationRemote Configuration and Management LAN-Based Remote Configuration and Management Telnet Remote ManagementMultiVOIP Telnet Server Menu Phone Directory Configuration Voice over IP ConfigurationWEB Management Phone Directory DatabaseRemote Configuration and Management One-Step Upgrade Upgrade ProceduresManual Upgrade Procedure Warranty, Service, and Tech Support Warranty, Service, and Tech Support On-line Warranty Registration Limited WarrantyRecording MultiVOIP Information Tech SupportContacting Technical Support About the Internet ServiceAppendixes Appendix a TCP/IP Description Appendix a TCP/IP Description Internet Protocol IP Command Port Cable Appendix B Cabling DiagramsVoice/Fax Channel Connectors LAN CableMagix 400 E&M Tie Card MVP 400/800 Magix 400 E&M Connection Wire Tire CardClass a Statement Appendix C Regulatory InformationFax Branding Statement FCC PartREN FCC Part 68 TelecomCanadian Limitations Notice EMC, Safety and Terminal Directive ComplianceRinger Equivalence Number Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Subscriber Loop See Local loop Glossary Glossary Index