Alliance Laundry Systems 9001889R7 manual Version of Control, Program Storing Mode

Page 9

Version of Control

To determine control version, apply power to machine. Control will display version of control (i.e., 1.15).

Language on Display (Version 1.15 and later ONLY)

To set a different language on the WE-8 display:

1.Turn key from RUN to PROGRAM.

2.Press “Auxiliary”, “2” and “9” to enter set-up mode.

3.English will display. Press “Advance” until desired language displays (French, Italian, Spanish and German).

4.Press “Enter” keypad.

5.Press “Enter” to advance through set-up mode.

6.Wait until information is saved.

7.Turn key from PROGRAM to RUN.

8.Display will read language chosen for all cycles.

Setup of the Chemical Hold Feature (Version 1.11 and later ONLY)

∙At power up, verify that model is at least version 1.11. Refer to version of Control Section. Earlier versions do not have this chemical hold feature.

∙Insert key into key switch and turn to Program.

∙Push the Auxiliary key, the 2 key, and the 9 key in succession to enter System Program Mode.

∙Push the Start key 10 times to arrive at the Chemical hold choice.

∙Push the Add Cycle/Advance key to toggle the Chemical hold feature either Yes (on) or No (off).

∙Push the Start key twice to save changes and exit System Program Mode.

∙Turn key switch to Run.

NOTE: If chemical hold is on, then a switch closure/opening between pins 1 and 4 of the COIN header on the output board will control supplies 4 through 9. A closure will turn the programmed supply/ies on and count down the time for the supply to be on. An opening will turn the programmed supply/ies off and halt the time for the supply to be on.

Programming

NOTE: If chemical hold is off, then supplies 4 through 9 are controlled exactly like supplies 1 through 3. A switch closure/opening between pins 1 and 4 of the COIN header on the output board will have no effect.

Program Storing Mode

The WE-8 control is capable of 99 total cycles. One cycle contains 1 or more steps.

One step is a function of the wash program (example: heat).

Choose between the following functions:

Fill:

To fill the machine with water.

Wash:

Wash action of the machine.

Supply:

To add detergent to the wash (liquid or

 

powder).

Cooldown: Cool to programmed temperature

Heat:

To heat the water.

Soak:

The wash will be soaked for a

 

programmed time and a programmed

 

temperature.

Aux:

A relay contact will close for a

 

programmed time.

Spin:

To spin the machine for a programmed

 

time and RPM.

Drain:

To drain the water from the machine.

9001889

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Washer-Extractors Page 9001889 Contents Model Identification IntroductionProgramming Setup of the MachinePress the Enter button to select options Programming Version of Control Program Storing ModeFill Explanation of the Step FunctionsProgramming Wash Chemical Hold Feature Soak Spin Example Making a New Program Cycle Heat Wash 4 10/20 Cycle Cycle Cycle 51 Spin Cycle 51 0 min Cycle 51 8 min 30 sec End Change a Complete Step Edit a CycleXxxxxxxx Changing the Time of a Step Press Enter to go to the next step Delete a Step Insert a Step Programming Delete a Cycle Reloading Previous Settings Reading Cycle Count Cycle CountCalibration of the Machine Speed Calibration Pre-Programmed Cycles Cycle Towels Light Soil Step Description Minsec Cycle Towels Medium Soil Step Description Minsec Cycle Blankets Warm Step Description Minsec Cycle Rinse and Spin Step Description Minsec Cycle Health Care Sheets Light Soil Step Description Minsec Cycle Health Care Towels Heavy Soil Step Description Minsec Cycle Health Care Cotton Blankets Step Description Minsec Cycle Health Care Personal No Bleach Step Description Minsec Cycle Health Care Pads Polyester Step Description Minsec Cycle Table Color Iron Step Description Minsec Cycle Table Color No Iron Step Description Minsec Pre-Programmed Cycles Visa No Iron Step Description Minsec Cycle Visa Color No Iron Step Description Minsec Cycle Shirt Color No Bleach Step Description Minsec Cycle Shirt Delicate Step Description Minsec Cycle Uniforms No Bleach Step Description Minsec Cycle Rags Heavy Soil Step Description Minsec Pre-Programmed Cycles Rewash/Reclaim Step Description Minsec Wash 1 18/3 32F 015 Drain 100 Pre-Programmed Cycles Energy Hot Step Description Minsec Cycle Energy Cold Step Description Minsec Pre-Programmed Cycles Normal 60C Step Description Minsec Cycle Gentle Cold Step Description Minsec Pre-Programmed Cycles Perm Press 60C Step Description Minsec Pre-Programmed Cycles Gentle 30C Step Description Minsec Inverter Drive Error Codes Indication During acceleration-If a current of more Indication
Top Page Image Contents