Linksys WAP200RF manual Navigating the Utility, Setup, Wireless

Page 19

Wireless-G Access Point with Power Over Ethernet and Rangebooster

3.Although it is not recommended, you can connect your PC wirelessly to the Access Point when the DHCP server is connected on the LAN side. It is not recommended, because you can easily lose your connection through configuration changes.

Launch your web browser, such as Internet Explorer or Mozilla Firefox and enter the Access Point’s default IP address, 192.168.1.245, in the Address field. Press the Enter key.

Enter admin in the User Name field. The first time you open the web-based utility, use the default password, admin. (You can set a new password from the Administration - Management tab.) Then click the OK button.

After setting up the Access Point to use DHCP or manually configure a new IP address, move your Access Point to the desired network. You will have to use the new IP address the next time you access the web-based utility.

Navigating the Utility

The web-based utility consists of the following five main tabs: Setup, Wireless, Security Monitor, Administration, and Status. Additional screens (sub tabs) will be available from most of the main tabs.

The following briefly describes the main & sub tabs of the Utility.

Setup

Enter the Host Name, IP Address settings, and set the time on this screen.

Basic Setup. Configure the host name and IP address settings for this Access Point.

Time. Set the time on this Access Point.

Wireless

You will use the Wireless tabs to enter a variety of wireless settings for the Access Point.

Basic Wireless Settings. Choose the wireless network mode (e.g. Mixed), SSID, and radio channel on this screen.

Wireless Security. Use this screen to configure the Access Point’s security settings.

Wireless Connection Control. Use this screen to control the wireless connections from client devices to this Access Point.

Chapter 5: Setting Up the Wireless-G Access Point

Figure 5-1: Login Screen

13

Navigating the Utility

Image 19
Contents User Guide Copyright and Trademarks How to Use this User GuideTable of Contents Appendix B Wireless Security Appendix a TroubleshootingFrequently Asked Questions List of Figures Example of a Simple Wireless Network20 Security Monitor Basic Settings Welcome IntroductionWhat’s in this User Guide? Introduction What’s in this User Guide? Network Topology Planning Your Wireless NetworkRoaming Network Layout Example of a simple wireless network LEDs Getting to Know the Wireless-G Access PointPorts Access Point’s port are located on the back of the deviceAntennas and Positions Desktop Placement and Antenna SetupOverview Connecting the Wireless-G Access PointConnection Stand Option Placement OptionsWall-Mount Option Accessing the Utility Setting Up the Wireless-G Access PointWireless SetupNavigating the Utility Administration AP ModeSecurity Monitor Status Network Setup Configuring the Wireless-G Access PointSetup Basic Setup Tab Basic SetupTime Setup Time TabBasic Settings Wireless Basic Wireless Settings TabWireless Security Wireless Wireless Security TabWPA2-Personal WPA-Personal aka WPA-PSKWPA-Enterprise WPA2-Personal MixedWPA2-Enterprise Mixed WPA2-EnterpriseRadius DisableConnection Control Wireless Wireless Connection Control TabWireless Connection Control Wireless Client ListAdvanced Settings Wireless Advanced Wireless Settings TabVlan Wireless Vlan & QoS TabQoS MAC Address AP Mode Tab18 Wireless Repeater Mode 19 Wireless Bridge Mode Wireless Security Monitor Security Monitor Basic Settings TabSecurity Monitor Accounts Mail Notification Security Monitor Event Log TabSyslog Notification Management Administration Management TabWeb Access Local AP PasswordIdentification SnmpNotification Queue Length Administration Log TabLog Email AlertFirmware Upgrade Administration Factory Default TabAdministration Firmware Upgrade Tab Factory DefaultConfig Management Administration Reboot TabAdministration Config Management Tab RebootInformation Status Local Network TabLocal Network Wireless Network Status Wireless TabSystem Performance WiredWireless Status System Performance TabPage Frequently Asked Questions Appendix a TroubleshootingWhat Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Page Appendix C Upgrading Firmware Shared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary 802.11F Wireless Roaming Appendix F SpecificationsSecurity Dhcp Client11g 14 dBm 11.g 54Mbps@ -72dBm, 11.b 11Mbps@ -85dBMSuspicious network events Wireless Security MonitorCertification Limited Warranty Appendix G Warranty InformationAppendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Need to contact Linksys? Appendix I Contact InformationInformation section in this Guide