Linksys WAP200RF manual QoS

Page 33

Wireless-G Access Point with Power Over Ethernet and Rangebooster

QoS

The following options are VLAN global settings for the Access Point.

Default CoS (Priority). Select Enabled if you want to assign a default CoS value to each SSID. This option is automatically enabled when the VLAN option is enabled. The default is Disabled.

U-APSD (Unscheduled Automatic Power Save Delivery). This option is only available when WMM is enabled on any of the SSIDs. Select Enabled if you want client devices with U-APSD capability to take advantage of the power save mode. The default is Disabled.

SSID Name. Displays the SSIDs defined under the Basic Wireless Settings tab. If an SSID has been disabled, the options cannot be configured.

VLAN ID. Select a number between 1 and 4094 to identify the VLAN. Multiple SSIDs can share the same VLAN value.

Priority. You can assign the default priority (802.1p COS bits) for packets coming in from each wireless network by selecting a number from the drop-down menu. The higher the number, the higher the priority will be. The default is 0.

Tx Rate Limiting. You can limit the maximum data rate used in your network to save bandwidth and power consumption on client devices. The actual data rate is determined by the Auto-Fallback mechanism between your Access Point and a client device. The default is 54 Mbps for Mixed or G-Only wireless mode, 11 Mbps for B-Only mode.

WMM. Wi-Fi Multimedia is a QoS feature defined by the WiFi Alliance before IEEE 802.11e was finalized. Now it is part of IEEE 802.11e. When this is enabled, it provides four priority queues for different types of traffic. It automatically maps the incoming packets to the appropriate queues based on QoS settings (in the IP or layer 2 header). WMM provides the capability to prioritize wireless traffic in your environment. The default is Disabled (unchecked).

Chapter 6: Configuring the Wireless-G Access Point

27

The Wireless - VLAN & QoS Tab

Image 33
Contents User Guide Copyright and Trademarks How to Use this User GuideTable of Contents Appendix a Troubleshooting Appendix B Wireless SecurityFrequently Asked Questions List of Figures Example of a Simple Wireless Network20 Security Monitor Basic Settings Welcome IntroductionWhat’s in this User Guide? Introduction What’s in this User Guide? Planning Your Wireless Network Network TopologyRoaming Network Layout Example of a simple wireless network LEDs Getting to Know the Wireless-G Access PointPorts Access Point’s port are located on the back of the deviceAntennas and Positions Desktop Placement and Antenna SetupConnecting the Wireless-G Access Point OverviewConnection Placement Options Stand OptionWall-Mount Option Accessing the Utility Setting Up the Wireless-G Access PointSetup WirelessNavigating the Utility AP Mode AdministrationSecurity Monitor Status Setup Basic Setup Tab Configuring the Wireless-G Access PointBasic Setup Network SetupTime Setup Time TabBasic Settings Wireless Basic Wireless Settings TabWireless Security Wireless Wireless Security TabWPA2-Personal WPA-Personal aka WPA-PSKWPA-Enterprise WPA2-Personal MixedWPA2-Enterprise Mixed WPA2-EnterpriseRadius DisableWireless Connection Control Wireless Wireless Connection Control TabWireless Client List Connection ControlAdvanced Settings Wireless Advanced Wireless Settings TabVlan Wireless Vlan & QoS TabQoS MAC Address AP Mode Tab18 Wireless Repeater Mode 19 Wireless Bridge Mode Security Monitor Basic Settings Tab Wireless Security MonitorSecurity Monitor Accounts Mail Notification Security Monitor Event Log TabSyslog Notification Web Access Administration Management TabLocal AP Password ManagementIdentification SnmpLog Administration Log TabEmail Alert Notification Queue LengthAdministration Firmware Upgrade Tab Administration Factory Default TabFactory Default Firmware UpgradeAdministration Config Management Tab Administration Reboot TabReboot Config ManagementStatus Local Network Tab InformationLocal Network Wireless Network Status Wireless TabWireless WiredStatus System Performance Tab System PerformancePage Frequently Asked Questions Appendix a TroubleshootingWhat Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Page Appendix C Upgrading Firmware Appendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary 802.11F Wireless Roaming Appendix F Specifications11g 14 dBm Dhcp Client11.g 54Mbps@ -72dBm, 11.b 11Mbps@ -85dBM SecurityWireless Security Monitor Suspicious network eventsCertification Limited Warranty Appendix G Warranty InformationAppendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix I Contact Information Need to contact Linksys?Information section in this Guide