Linksys WAP200RF manual Appendix H Regulatory Information

Page 68

Wireless-G Access Point with Power Over Ethernet and Rangebooster

Industry Canada Statement

This device complies with Industry Canada ICES-003 and RSS210 rules.

Déclaration d’Industrie Canada

Cet appareil est conforme aux normes NMB003 et RSS210 d'Industrie Canada.

Industry Canada Statement

Operation is subject to the following two conditions:

1.This device may not cause interference and

2.This device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication.

3.Industry Canada Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Avis d'Industrie Canada

L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes:

1.il ne doit pas produire de brouillage et

2.il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Le dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximum de 2 dBi. Les règlements d'Industrie Canada interdisent strictement l'utilisation d'antennes dont le gain est supérieur à cette limite. L'impédance requise de l'antenne est de 50 ohms.

Afin de réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour obtenir une communication satisfaisante.

3.Avis d'Industrie Canada concernant l'exposition aux radiofréquences :

Ce matériel est conforme aux limites établies par IC en matière d'exposition aux radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d'au moins 20 cm entre l'antenne et le corps de l'utilisateur.

L'émetteur ne doit pas être placé près d'une autre antenne ou d'un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur.

Appendix H: Regulatory Information

62

Page 67 Page 69
Image 68
Page 67 Page 69
Contents User Guide How to Use this User Guide Copyright and TrademarksTable of Contents Frequently Asked Questions Appendix a TroubleshootingAppendix B Wireless Security Example of a Simple Wireless Network List of Figures20 Security Monitor Basic Settings Introduction WelcomeWhat’s in this User Guide? Introduction What’s in this User Guide? Roaming Planning Your Wireless NetworkNetwork Topology Network Layout Example of a simple wireless network Getting to Know the Wireless-G Access Point LEDsAccess Point’s port are located on the back of the device PortsDesktop Placement and Antenna Setup Antennas and PositionsConnection Connecting the Wireless-G Access PointOverview Wall-Mount Option Placement OptionsStand Option Setting Up the Wireless-G Access Point Accessing the UtilityNavigating the Utility SetupWireless Security Monitor AP ModeAdministration Status Configuring the Wireless-G Access Point Setup Basic Setup TabBasic Setup Network SetupSetup Time Tab TimeWireless Basic Wireless Settings Tab Basic SettingsWireless Wireless Security Tab Wireless SecurityWPA-Personal aka WPA-PSK WPA2-PersonalWPA2-Personal Mixed WPA-EnterpriseWPA2-Enterprise WPA2-Enterprise MixedDisable RadiusWireless Wireless Connection Control Tab Wireless Connection ControlWireless Client List Connection ControlWireless Advanced Wireless Settings Tab Advanced SettingsWireless Vlan & QoS Tab VlanQoS AP Mode Tab MAC Address18 Wireless Repeater Mode 19 Wireless Bridge Mode Security Monitor Accounts Security Monitor Basic Settings TabWireless Security Monitor Security Monitor Event Log Tab Mail NotificationSyslog Notification Administration Management Tab Web AccessLocal AP Password ManagementSnmp IdentificationAdministration Log Tab LogEmail Alert Notification Queue LengthAdministration Factory Default Tab Administration Firmware Upgrade TabFactory Default Firmware UpgradeAdministration Reboot Tab Administration Config Management TabReboot Config ManagementLocal Network Status Local Network TabInformation Status Wireless Tab Wireless NetworkWired WirelessStatus System Performance Tab System PerformancePage Appendix a Troubleshooting Frequently Asked QuestionsWhat Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Security Threats Facing Wireless Networks Appendix B Wireless SecuritySecurity Precautions Appendix B Wireless Security Page Appendix C Upgrading Firmware Network Neighborhood/My Network Places Appendix D Windows HelpShared Resources Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix F Specifications 802.11F Wireless RoamingDhcp Client 11g 14 dBm11.g 54Mbps@ -72dBm, 11.b 11Mbps@ -85dBM SecurityCertification Wireless Security MonitorSuspicious network events Appendix G Warranty Information Limited WarrantyAppendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Information section in this Guide Appendix I Contact InformationNeed to contact Linksys?
Top Page Image Contents