Linksys WAP200RF manual AP Mode Tab, MAC Address

Page 34

Wireless-G Access Point with Power Over Ethernet and Rangebooster

The AP Mode Tab

On this screen you can change the Access Point’s mode of operation. In most cases, you can keep the default setting - Access Point. You may wish to change the Access Point’s mode of operation if you want to use the Access Point as a wireless repeater to extend the range of your wireless network. You may also wish to change the Access Point’s mode of operation if you want to use the Access Point as a wireless bridge; for example, you can use two Access Points in Wireless Bridge mode to connect two wired networks that are in two different buildings.

AP Mode

The Access Point offers three modes of operation: Access Point, Wireless Repeater, and Wireless Bridge. For the Repeater and Bridge modes, make sure the SSID, channel, and security settings are the same for the other wireless access points/devices.

IMPORTANT: For the AP Client and Wireless Bridge modes, the remote access point must be a second Linksys Wireless-G Access Point. For the Wireless Repeater mode, the remote wireless bridge must be a second Linksys Wireless-G Access Point or Wireless-G Router.

MAC Address

The MAC address of the Access Point is displayed here.

Access Point. The Mode is set to Access Point by default. This connects your wireless PCs to a wired network. In most cases, no change is necessary.

Allow wireless signal to be repeated by a repeater. Select this option if you want to use another wireless device to repeat the signal of this Access Point. You will need to enter the MAC address(es) of the repeating device(s). Up to 3 repeaters can be used.

Chapter 6: Configuring the Wireless-G Access Point

Figure 6-17: AP Mode

28

The AP Mode Tab

Image 34
Contents User Guide How to Use this User Guide Copyright and TrademarksTable of Contents Appendix B Wireless Security Appendix a TroubleshootingFrequently Asked Questions Example of a Simple Wireless Network List of Figures20 Security Monitor Basic Settings Introduction WelcomeWhat’s in this User Guide? Introduction What’s in this User Guide? Network Topology Planning Your Wireless NetworkRoaming Network Layout Example of a simple wireless network Getting to Know the Wireless-G Access Point LEDsAccess Point’s port are located on the back of the device PortsDesktop Placement and Antenna Setup Antennas and PositionsOverview Connecting the Wireless-G Access PointConnection Stand Option Placement OptionsWall-Mount Option Setting Up the Wireless-G Access Point Accessing the UtilityWireless SetupNavigating the Utility Administration AP ModeSecurity Monitor Status Basic Setup Configuring the Wireless-G Access PointSetup Basic Setup Tab Network SetupSetup Time Tab TimeWireless Basic Wireless Settings Tab Basic SettingsWireless Wireless Security Tab Wireless SecurityWPA-Personal aka WPA-PSK WPA2-PersonalWPA2-Personal Mixed WPA-EnterpriseWPA2-Enterprise WPA2-Enterprise MixedDisable RadiusWireless Client List Wireless Wireless Connection Control TabWireless Connection Control Connection ControlWireless Advanced Wireless Settings Tab Advanced SettingsWireless Vlan & QoS Tab VlanQoS AP Mode Tab MAC Address18 Wireless Repeater Mode 19 Wireless Bridge Mode Wireless Security Monitor Security Monitor Basic Settings TabSecurity Monitor Accounts Security Monitor Event Log Tab Mail NotificationSyslog Notification Local AP Password Administration Management TabWeb Access ManagementSnmp IdentificationEmail Alert Administration Log TabLog Notification Queue LengthFactory Default Administration Factory Default TabAdministration Firmware Upgrade Tab Firmware UpgradeReboot Administration Reboot TabAdministration Config Management Tab Config ManagementInformation Status Local Network TabLocal Network Status Wireless Tab Wireless NetworkStatus System Performance Tab WiredWireless System PerformancePage Appendix a Troubleshooting Frequently Asked QuestionsWhat Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Page Appendix C Upgrading Firmware Shared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix F Specifications 802.11F Wireless Roaming11.g 54Mbps@ -72dBm, 11.b 11Mbps@ -85dBM Dhcp Client11g 14 dBm SecuritySuspicious network events Wireless Security MonitorCertification Appendix G Warranty Information Limited WarrantyAppendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Need to contact Linksys? Appendix I Contact InformationInformation section in this Guide