Linksys WAP200RF manual Appendix H Regulatory Information

Page 67

Wireless-G Access Point with Power Over Ethernet and Rangebooster

Appendix H: Regulatory Information

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment or devices

•Connect the equipment to an outlet other than the receiver's

•Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11.

Safety Notices

Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Do not use this product near water, for example, in a wet basement or near a swimming pool.

Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Appendix H: Regulatory Information

61

Page 66 Page 68
Image 67
Page 66 Page 68
Contents User Guide Copyright and Trademarks How to Use this User GuideTable of Contents Appendix B Wireless Security Appendix a TroubleshootingFrequently Asked Questions List of Figures Example of a Simple Wireless Network20 Security Monitor Basic Settings Welcome IntroductionWhat’s in this User Guide? Introduction What’s in this User Guide? Network Topology Planning Your Wireless NetworkRoaming Network Layout Example of a simple wireless network LEDs Getting to Know the Wireless-G Access PointPorts Access Point’s port are located on the back of the deviceAntennas and Positions Desktop Placement and Antenna SetupOverview Connecting the Wireless-G Access PointConnection Stand Option Placement OptionsWall-Mount Option Accessing the Utility Setting Up the Wireless-G Access PointWireless SetupNavigating the Utility Administration AP ModeSecurity Monitor Status Network Setup Configuring the Wireless-G Access PointSetup Basic Setup Tab Basic SetupTime Setup Time TabBasic Settings Wireless Basic Wireless Settings TabWireless Security Wireless Wireless Security TabWPA2-Personal WPA-Personal aka WPA-PSKWPA-Enterprise WPA2-Personal MixedWPA2-Enterprise Mixed WPA2-EnterpriseRadius DisableConnection Control Wireless Wireless Connection Control TabWireless Connection Control Wireless Client ListAdvanced Settings Wireless Advanced Wireless Settings TabVlan Wireless Vlan & QoS TabQoS MAC Address AP Mode Tab18 Wireless Repeater Mode 19 Wireless Bridge Mode Wireless Security Monitor Security Monitor Basic Settings TabSecurity Monitor Accounts Mail Notification Security Monitor Event Log TabSyslog Notification Management Administration Management TabWeb Access Local AP PasswordIdentification SnmpNotification Queue Length Administration Log TabLog Email AlertFirmware Upgrade Administration Factory Default TabAdministration Firmware Upgrade Tab Factory DefaultConfig Management Administration Reboot TabAdministration Config Management Tab RebootInformation Status Local Network TabLocal Network Wireless Network Status Wireless TabSystem Performance WiredWireless Status System Performance TabPage Frequently Asked Questions Appendix a TroubleshootingWhat Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Page Appendix C Upgrading Firmware Shared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary 802.11F Wireless Roaming Appendix F SpecificationsSecurity Dhcp Client11g 14 dBm 11.g 54Mbps@ -72dBm, 11.b 11Mbps@ -85dBMSuspicious network events Wireless Security MonitorCertification Limited Warranty Appendix G Warranty InformationAppendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Need to contact Linksys? Appendix I Contact InformationInformation section in this Guide
Top Page Image Contents