Alcatel Carrier Internetworking Solutions 1000 ADSL manual Point to Point Service

Page 13

POINT TO POINT SERVICE

If your service provider is providing point to point (PPP) service, your ADSL modem should have model number 3EC 18202 BB or 3EC 18202 DB on the bottom of the modem case.

System Requirements

The Alcatel 1000 ADSL high speed modem requires a PC or workstation equipped with the following:

1.Ethernet 10Base-T network adapter card,

2.Operating system such as Windows 95, Windows 98, or Windows NT (see note)

3.Microsoft Virtual Private network (VPN) Adapter

Note:

If you have an operating system other than Windows 95, Windows 98, or Windows NT, contact your service provider for additional system requirements.

PPP service requires a user account to the service provider of your choice.

Hardware Installation

To connect your high speed ADSL modem, follow these steps:

1.Make sure the modem on/off switch is set to the O (off) position.

2.Connect the jack end of the power cable to the modem power socket.

3.Plug the other end of the power cable (the end with the power supply adapter) to an electrical outlet.

4.Connect one end of a standard telephone cable (not provided) to the modem connector labeled LINE.

Note:

The line cable may be provided by your service provider during installation, or it can be purchased at your local electronics supply store.

5.Connect the other end of the line cable to a phone jack.

Image 13
Contents Page Save These Important Safety Instructions Page Contents Modem Connections Troubleshooting Tips Getting Started Placement of Adsl High Speed ModemDelivery Check Table a If you mount Modem on Mark positions of holes Wall-Mounting OptionWall-Mounting Instructions Filter InstallationDetermining Your Service Type Bridged ServiceTable B Service Type Model NumberSystem Requirements Hardware InstallationPower/Sync Light Accessing Online Services10BASE-T Light Network Address AssignmentsPoint to Point Service Accessing Online Services Contents frame, select Free Downloads Windows 95/Windows 98 Dial-Up ProceduresSelect Start, Settings, Control Panel, Network Installing Dial-Up Networking Software Windows 98 OnlyClick on Communications in the Components list Make New Connection Windows 95 Example Configure the ConnectionVPN Server Field Windows 98 example Page Connect To Windows 98 Example Break the Connection Windows NT Dial-Up ProceduresAdd Point To Point Tunneling Protocol Network Window Select Network Protocol Window Remote Access Setup Window Configure Port Usage Window Dial-Up Networking Window Make the Connection Break the Connection ATM-25 Service ATMF-25 Light Description of Features General Network Architecture Modem ConnectionsConnectors on Adsl Modem Connector PinoutTable C. Connector Pinout Power SupplySignal Name PinVisual Indicators Table D Meaning Name Color Visual IndicatorsEthernet Interface Subscriber Line InterfaceMultiple PC Configuration Single PC ConfigurationStraight-Through Cable Layout Multiple PC Configuration ATMF-25 Interface Crossover Cable LayoutVirtual Connections Network ConnectionsTable E. Atmf VPI/VCI Values Parameter Meaning ATM-Forum InterfaceISP/Corporate Network Requirements Bridged ConnectionsTable F. Ethernet Parameters Connection VCIsNumber of Machines Supported MultiprotocolTable G. Ethernet VPI/VCI Values Parameter Meaning Table H. Ethernet ParametersPlug and Play PC/Workstation ConfigurationFixed IP Address Dynamic IP AddressFiltering Function Bridged Service with FilteringMulticast Traffic on Bridge Ports Unicast Traffic on Bridge Ports Broadcast Traffic on Bridge PortsIntroduction Point to Point Tunneling ConnectionsPPP/PPTP Network Any Connection Establishing PPP/PPTP ConnectionsATM Channels over Multiple Remote Destinations Pptp Destination Table LAN Protocols Supported Number of PPP/PPTP Connections SupportedKnown Limitations Overview Advanced ConfigurationsOne Tunnel Tunneling within a TunnelIP Parameters Subnetmask and Default Gateway ParametersDefault Netmask Sample ConfigurationsSingle PC Small Workgroup AllocationAdvanced Networks Automatic IP Parameter DistributionMost TCP / IP packages support the ARP and Ping command Ping-of-Life ProcedureArp -a -N interface IP address For example arp -a -NPing Arp -d modem IP address -N interface IP addressArp -a any IP address 01-90-D0-00-01-FF Ping-to-Defaults ProcedurePing any IP address Configuring the Browser Changing the Modem SettingsAccessing the Adsl Modem Interface Netscape NavigatorApply DefaultsSave AdvancedInitial Setup Basic ConfigurationWelcome BridgeIP Address User Defined Configuration TableNetmask/Subnet Mask BOOTP/DHCP Configuration Table Default GatewaySubnet Mask IP Address Table Advanced ConfigurationAddress NetmaskAction Bridge ConfigurationIP Route Table Port States TableEncap Bridge PortAging Table StateChannel ID Basic PPP/PPTP ConfigurationName Hdlc Advanced PPP/PPTP ConfigurationHdlc Framing System OverviewRegulatory Information Safety StandardsEnvironmental Conditions Page For Canadian Modem Users Avertissement Pour les Utilisateurs Canadiens de ModemSolution Problem3EC 16389 Abaa Tczza