D-Link DVG-2032S Static IP Settings Function Command Select a Static IP, IP address Settings

Page 15

11

IP Configuration Settings—Setting IP Configuration of WAN Port

Static IP Settings

NOTE: Complete static IP settings should include a static IP (Option 1 under114), IP address (111), Subnet Mask (112), and Default Gateway (113). Please contact your local Internet Service Provider (ISP) if you have any questions.

Function

Command

Select a Static IP

After entering IVR mode, dial 114.

 

After hearing “Enter value”, dial 1 (to select static IP)

IP address Settings

After entering IVR mode, dial 111. After hearing “Enter value”, enter your IP

 

address, followed by “#”.

 

Example: If the IP address is 192.168.1.200, dial 192*168*1*200#.

Subnet Mask Settings

After entering IVR mode, dial 112. After hearing “Enter value”, enter your

 

subnet mask, followed by “#”.

 

Example: If the mask value is 255.255.255.0, dial 255*255*255*0#.

 

 

Default Gateway Settings

After entering IVR mode, dial 113. After hearing “Enter value”, enter your

 

default gateway’s IP address, followed by “#”.

 

Example: If the Default Gateway is 192.168.1.254, dial 192*168*1*254#.

Save Settings and Restart

To save settings, dial 509 (Save Settings). The system will save the

 

settings. Please restart the system. Wait for about 40 seconds for the

 

system to restart, and then enter 101 to check if the IP address is retained.

 

If the IP address is not repeated, it indicates that Gateway has not been

 

properly connected, please check if the cable connection, account, or

 

password are correct.

Dynamic IP (DHCP) Settings

After entering IVR mode, dial 114.

After hearing “Enter value”, dial 2 (to select DHCP).

Saving settings –press 509 (Save Settings). Please restart the system. After the system is restarted, press 101 to check if the IP address is retained.

If the system does not repeat the IP address, it indicates Gateway has not been properly connected to the Internet. Please check the cable connection.

ADSL PPPoE Settings

NOTE: Complete PPPoE settings should include: Select PPPoE (Option 3 of 114), PPPoE account (121) and PPPoE password (122).

Please contact your local Internet Service Provider (ISP) if you have any questions.

Select a PPPoE

After entering IVR mode, dial 114.

After hearing “Enter value”, dial 3 (to select PPPoE).

Page 14 Page 16
Image 15
Page 14 Page 16
Contents DVG-2032S Voip Gateway Page Contents Coding Principle Product Overview IntroductionCall features optional Product FeaturesHardware Description Front PanelRear Panel Gateway Assigned with a Public IP Address Network InterfaceGateway in a NAT network Integrating the DVG-2032S with PBX DVG-2032S connecting directly to phone setsTelephone Interface Description Example for DVG-2032SBasic Settings of a Gateway IVR Interactive Voice ResponsePreparation Save Settings InstructionsTo inquire about current Gateway’s WAN Port IP address Function Code Description Example IVR Functions TableFunction Code Description Example Default Gateway Settings Static IP Settings Function Command Select a Static IPIP address Settings Subnet Mask SettingsPPPoE Account Settings PPPoE Character Conversion Table Instructions Network Settings WANPage Adsl PPPoE Settings IP Configuration Setting WAN PortSetting Dynamic IP Dhcp Setting Static IPDNS Settings BigPond for Australia use onlyClone MAC Using Phone Books Manager Network Settings LAN LAN interface mode※LAN IP/Subnet mask WAN QoS QoS SettingsNAT Traversal NAT/DDNSDdns Telephony Settings Hotline Functions SIP 164 System Each line registers to Proxy independently FXS Representative number registers to ProxyCalling Features Calling Feature Instructions Advanced Options Codec Line SettingsFax Settings Drop Silent Call Timeout Set the time to hang up the phone Digit Map Phone BookSpeed Dial ACL for Management Caller FilterCDR Settings CPT/Cadence SettingsLanguage System Information RTP Packet Summary Stun InquiryPing Test Snmp Backup/RestoreSystem Operations Save Settings Provision SettingsLogout Software UpgradeIP Sharing Functions Select TCP/IP, and then click Properties Page Dialed Number Processing Flow InstructionEnd
Top Page Image Contents