ADTRAN 4106 Plan A, 4206 Plan A Carrier Wavelength λ, Path Distance d, System Losses L

Page 18

Section 2 Microwave Path Engineering Basics

TRACER 4106/4206 System Manual

 

 

Carrier Wavelength (λ)

The carrier wavelength is the physical wavelength of the main RF carrier being used for communication, and is usually approximated at the center frequency of the band (which is 2441.75 MHz for the TRACER 4106 and 5787.5 MHz for the TRACER 4206). The carrier wavelength calculations follow:

λ= c / f (meters)

where

c = speed of light (in meters) f = frequency (in Hz)

resulting in the following carrier wavelength (at 5787.5 MHz):

λ= 3.00 x 10¯8 / 5787.5 x 10 5

=0.0518 m or 5.18 cm

Path Distance (d)

The path distance is simply the physical distance between the transmit and receive antennas. For the TRACER 4106/4206, these distances can range up to 30 miles.

System Losses (L)

System losses are defined by RF coaxial cable loss, connector losses, and losses added from any additional lightning protection devices for the power budget analysis. Coaxial cable is required to attach the TRACER 4106/4206 to the antenna. The length of the cable varies from a few feet to hundreds of feet, depending upon your application and the proximity of the TRACER 4106/4206 to the antenna. Various grades of coaxial cable will work sufficiently well for connecting the TRACER 4106/4206 unit to the antenna. A low-loss coaxial cable will minimize cable losses.

One end of the coaxial cable requires an N-type male connector (plug) to mate with the

TRACER 4106/4206 unit. The other end of the coaxial cable requires a connector compatible with the antenna chosen for the installation (usually an N-type male connector). Additionally, ADTRAN recommends that the outdoor connector on the coaxial cable be weatherproofed to prevent corrosion and electrical shorting.

In areas where lightning strikes are frequent, a lightning arrestor should be installed directly on the antenna coaxial cable. Installing lightning arrestors helps protect the RF electronics in the downstream path from damaging voltages and currents (including the TRACER 4106/4206 unit).

18

© 2004 ADTRAN, Inc.

612804206L2-1A

Image 18
Contents Tracer 4106/4206 Trademarks To the Holder of the ManualAbout this Manual Revision History Safety Instructions Save These Important Safety InstructionsFCC-Required Information Radio Frequency Interface StatementFCC Output Power Restrictions Exposure to Radio Frequency FieldsRepair and Return Pre-Sales Inquiries and Applications SupportInstallation and Maintenance Support Post-Sale SupportTraining Table of Contents Table of Contents Tracer 4106/4206 System Manual System Description System Overview Features and BenefitsConfiguration and Management OperationalReceiver Sensitivity Antenna Information Receiver PowerLine-of-Sight Other ConsiderationsADTRAN, Inc Decibels LINE-OF-SIGHTTerminology Calculating the Fade MarginReceiver Power Transmitted Power PT Antenna GainCarrier Wavelength λ Path Distance dSystem Losses L Path Loss LP Typical Coaxial Loss for Common Cable TypesReceiver Sensitivity T1 PortsTracer Rssi Test Points Antenna InformationAntenna Alignment Antenna Beam PatternsFresnel Zones, Earth Curvature, & Antenna Heights Other Considerations Path AvailabilityTerrain Terrain Factor Description Values normally used are listed below Climate Climate Factor DescriptionAt-A-Glance Specifications Reviewing the Front Panel DesignReviewing the Front Panel Design Equipment DimensionsPower Requirements Rssi Monitoring InterfaceReviewing the Tracer 4106/4206 Rear Panel Design Rear Panel Description Name Connector DescriptionRS-232 Connection DB-25 Terminal Use RS-232 Connection PinoutTracer 4106/4206 DCE to Terminal DTE Diagram DB-25 RS-232 Connection Modem UseTracer 4106/4206 DCE to Personal Computer DB-9 T1 Interface Connector Pinout T1 Connections RJ-48CTracer 4106/4206 DCE to Modem DCE DB-25 Antenna Interface N-Type connector Alarm Contacts Plug-In Terminal BlockDC Power Connection Plug-In Terminal Block FuseAT-A-GLANCE Specifications Hardware Description Specification TransmitterVT100 Terminal Interface Engineering Guidelines Tracer 4106/4206 System Manual Network Turnup Procedure Unpack and Inspect the SystemTools Required Contents of Adtran ShipmentIntroduction Unpack and Inspect the SystemCustomer Provides Channel SelectionGrounding Instructions Supplying Power to the Unit Mounting OptionsInstructions for Rackmounting the Tracer 4106/4206 Connecting the T1 Interface Inch Rackmount IllustrationUser Interface Guide Menu DescriptionsNavigating the Terminal Menu Terminal Menu WindowTerminal Menu and System Control Navigating using the Keyboard KeysPassword Protection To do this Press this keyContact Information Menu DescriptionsElapsed Time RF StatusTx Power T1 Status Error/Alarm OnlyRx Power Remote Tracer StatusMain Menu Tracer System Options Tracer System Options RF Bandplan Receiver Sensitivity for the Tracer 4106/4206 Receiver Sensitivity Active BandwidthResets all system error counters for the Tracer 4106/4206 T1x Status/Configuration/Loopback T1 Interface AlarmsT1X STATUS/CONFIGURATION/LOOPBACK T1X Line Build OUT T1 Remote Link Loopback T1X Performance History Installing/Troubleshooting the Tracer Hardware OverviewTST LED LED Indicators PWR LEDOverview RF Down LEDT1 Interface Alarm LEDs RF LOW LEDRF Errors STEP-BY-STEP TroubleshootingINSTALLING/TROUBLESHOOTING the Tracer Hardware Installing/Configuring T1 Hardware