ADTRAN 4106 Plan A, 4206 Plan A system manual Navigating the Terminal Menu, Terminal Menu Window

Page 42

Section 5 User Interface Guide

TRACER 4106/4206 System Manual

 

 

1.NAVIGATING THE TERMINAL MENU

The TRACER 4106/4206 menu system can be accessed with a VT100 compatible terminal that is connected to the RS-232 port located on the back of the unit and set to 9600 bits per second, 8 data bits, 1 stop bit, and no parity. Flow control on the serial interface should be configured to NONE for proper operation. Once a terminal is connected, press <Ctrl + L> to refresh the current screen. If password access has been enabled, the ENTER PASSWORD message displays at the bottom of the TRACER 4106/4206 System Status menu.

All TRACER 4106/4206 systems are shipped factory default with password protection disabled.

Terminal Menu Window

The TRACER 4106/4206 uses a series of menu pages and a single main menu page to access its many features. The main menu page (see Figure 1) provides a link to all available configuration/status pages.

After connecting a VT100 terminal to the TRACER 4106/4206, press <Ctrl + L> to redraw the current screen.

Figure 1. Main Menu Screen

42

© 2004 ADTRAN, Inc.

612804206L2-1A

Image 42
Contents Tracer 4106/4206 Trademarks To the Holder of the ManualAbout this Manual Revision History Safety Instructions Save These Important Safety InstructionsFCC-Required Information Radio Frequency Interface StatementFCC Output Power Restrictions Exposure to Radio Frequency FieldsRepair and Return Pre-Sales Inquiries and Applications SupportInstallation and Maintenance Support Post-Sale SupportTraining Table of Contents Table of Contents Tracer 4106/4206 System Manual System Description System Overview Features and BenefitsConfiguration and Management OperationalReceiver Sensitivity Antenna Information Receiver PowerLine-of-Sight Other ConsiderationsADTRAN, Inc Decibels LINE-OF-SIGHTTerminology Calculating the Fade MarginReceiver Power Transmitted Power PT Antenna GainCarrier Wavelength λ Path Distance dSystem Losses L Path Loss LP Typical Coaxial Loss for Common Cable TypesReceiver Sensitivity T1 PortsTracer Rssi Test Points Antenna InformationAntenna Alignment Antenna Beam PatternsFresnel Zones, Earth Curvature, & Antenna Heights Other Considerations Path AvailabilityTerrain Terrain Factor Description Values normally used are listed below Climate Climate Factor DescriptionAt-A-Glance Specifications Reviewing the Front Panel DesignReviewing the Front Panel Design Equipment DimensionsPower Requirements Rssi Monitoring InterfaceReviewing the Tracer 4106/4206 Rear Panel Design Rear Panel Description Name Connector DescriptionRS-232 Connection DB-25 Terminal Use RS-232 Connection PinoutTracer 4106/4206 DCE to Terminal DTE Diagram DB-25 RS-232 Connection Modem UseTracer 4106/4206 DCE to Personal Computer DB-9 T1 Interface Connector Pinout T1 Connections RJ-48CTracer 4106/4206 DCE to Modem DCE DB-25 Antenna Interface N-Type connector Alarm Contacts Plug-In Terminal BlockDC Power Connection Plug-In Terminal Block FuseAT-A-GLANCE Specifications Hardware Description Specification TransmitterVT100 Terminal Interface Engineering Guidelines Tracer 4106/4206 System Manual Network Turnup Procedure Unpack and Inspect the SystemTools Required Contents of Adtran ShipmentIntroduction Unpack and Inspect the SystemCustomer Provides Channel SelectionGrounding Instructions Supplying Power to the Unit Mounting OptionsInstructions for Rackmounting the Tracer 4106/4206 Connecting the T1 Interface Inch Rackmount IllustrationUser Interface Guide Menu DescriptionsNavigating the Terminal Menu Terminal Menu WindowTerminal Menu and System Control Navigating using the Keyboard KeysPassword Protection To do this Press this keyContact Information Menu DescriptionsElapsed Time RF StatusTx Power T1 Status Error/Alarm OnlyRx Power Remote Tracer StatusMain Menu Tracer System Options Tracer System Options RF Bandplan Receiver Sensitivity for the Tracer 4106/4206 Receiver Sensitivity Active BandwidthResets all system error counters for the Tracer 4106/4206 T1x Status/Configuration/Loopback T1 Interface AlarmsT1X STATUS/CONFIGURATION/LOOPBACK T1X Line Build OUT T1 Remote Link Loopback T1X Performance History Installing/Troubleshooting the Tracer Hardware OverviewTST LED LED Indicators PWR LEDOverview RF Down LEDT1 Interface Alarm LEDs RF LOW LEDRF Errors STEP-BY-STEP TroubleshootingINSTALLING/TROUBLESHOOTING the Tracer Hardware Installing/Configuring T1 Hardware