ADTRAN 4206 Plan A, 4106 Plan A FCC-Required Information, Radio Frequency Interface Statement

Page 5

TRACER 4106/4206 System Manual

FCC-Required Information

 

 

FCC-Required Information

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Radio Frequency Interface Statement

This equipment has been tested and found to comply with the limits for an intentional radiator, pursuant to Part 15, Subpart C of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.

The limits are designed to provide reasonable protection against such interference in a residential situation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna of the affected radio or television.

Increase the separation between the equipment and the affected receiver.

Connect the equipment and the affected receiver to power outlets on separate circuits.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by ADTRAN could void the user’s authority to operate the equipment.

612804206L2-1A

© 2003 ADTRAN, Inc.

5

Image 5
Contents Tracer 4106/4206 About this Manual TrademarksTo the Holder of the Manual Revision History Save These Important Safety Instructions Safety InstructionsRadio Frequency Interface Statement FCC-Required InformationExposure to Radio Frequency Fields FCC Output Power RestrictionsPre-Sales Inquiries and Applications Support Repair and ReturnTraining Installation and Maintenance SupportPost-Sale Support Table of Contents Table of Contents Tracer 4106/4206 System Manual System Description Configuration and Management Features and BenefitsSystem Overview OperationalLine-of-Sight Receiver PowerReceiver Sensitivity Antenna Information Other ConsiderationsADTRAN, Inc Terminology LINE-OF-SIGHTDecibels Calculating the Fade MarginReceiver Power Antenna Gain Transmitted Power PTSystem Losses L Carrier Wavelength λPath Distance d Typical Coaxial Loss for Common Cable Types Path Loss LPT1 Ports Receiver SensitivityAntenna Alignment Antenna InformationTracer Rssi Test Points Antenna Beam PatternsFresnel Zones, Earth Curvature, & Antenna Heights Terrain Terrain Factor Description Other ConsiderationsPath Availability Climate Climate Factor Description Values normally used are listed belowReviewing the Front Panel Design At-A-Glance SpecificationsPower Requirements Equipment DimensionsReviewing the Front Panel Design Rssi Monitoring InterfaceReviewing the Tracer 4106/4206 Rear Panel Design RS-232 Connection DB-25 Terminal Use Name Connector DescriptionRear Panel Description RS-232 Connection PinoutTracer 4106/4206 DCE to Personal Computer DB-9 Tracer 4106/4206 DCE to Terminal DTE Diagram DB-25RS-232 Connection Modem Use Tracer 4106/4206 DCE to Modem DCE DB-25 T1 Interface Connector PinoutT1 Connections RJ-48C DC Power Connection Plug-In Terminal Block Alarm Contacts Plug-In Terminal BlockAntenna Interface N-Type connector FuseHardware Description Specification Transmitter AT-A-GLANCE SpecificationsVT100 Terminal Interface Engineering Guidelines Tracer 4106/4206 System Manual Unpack and Inspect the System Network Turnup ProcedureIntroduction Contents of Adtran ShipmentTools Required Unpack and Inspect the SystemChannel Selection Customer ProvidesGrounding Instructions Instructions for Rackmounting the Tracer 4106/4206 Supplying Power to the UnitMounting Options Inch Rackmount Illustration Connecting the T1 InterfaceMenu Descriptions User Interface GuideTerminal Menu Window Navigating the Terminal MenuPassword Protection Navigating using the Keyboard KeysTerminal Menu and System Control To do this Press this keyElapsed Time Menu DescriptionsContact Information RF StatusRx Power T1 Status Error/Alarm OnlyTx Power Remote Tracer StatusMain Menu Tracer System Options Tracer System Options RF Bandplan Receiver Sensitivity Active Bandwidth Receiver Sensitivity for the Tracer 4106/4206Resets all system error counters for the Tracer 4106/4206 T1 Interface Alarms T1x Status/Configuration/LoopbackT1X STATUS/CONFIGURATION/LOOPBACK T1X Line Build OUT T1 Remote Link Loopback T1X Performance History Overview Installing/Troubleshooting the Tracer HardwareOverview LED Indicators PWR LEDTST LED RF Down LEDRF LOW LED T1 Interface Alarm LEDsSTEP-BY-STEP Troubleshooting RF ErrorsINSTALLING/TROUBLESHOOTING the Tracer Hardware Installing/Configuring T1 Hardware