3Com T1/PRI manual Menu Option 4 Checking DS0/modem channel status

Page 38

4-4CHAPTER 4: DUAL T1/PRI STATUS DISPLAYS

■Dual PRI

A Dual T1/PRI NAC is installed and assigned to that particular slot.

■ISDN-GW

A NETServer PRI NAC is installed and assigned to that particular slot.

■QBCH-MDM

A Quad Modem NAC is installed and assigned to that particular slot.

■QBCH-I_MDM

A Quad I-Modem NAC is installed and assigned to that particular slot.

Menu Option 4 Checking DS0/modem channel status

Status menu option 4 allows you to monitor the status of DS0s/modem channels for both spans. The DS0 to modem channel mappings are configured in option 8 of the span line 1 and 2 configuration menus.

The ID column represents the individual time slots on both spans.

The slot/chan column represents the modem slot/channel mapped to the individual time slots.

The status column displays one of these:

■AVAIL

The modem is installed and is idle.

■Un-Avail

There is no modem mapped to the time slot or the modem is not responding.

■In-Use

The modem is installed and is active.

Menu Option 5 Checking the chassis’ ISDN gateway status

Status menu option 5 allows you to check the status of the chassis’ ISDN gateway(s) (NETServer PRI(s)).

Image 38

Contents Dual T1/PRI Version NumberDual T1/PRI 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Configuring the span line’s interface ID Dual T1/PRI Maintenance Trouble Clearing Page Information This Reference About this ReferenceFinding Specific If you are looking for Turn toIcon Description ConventionsThis table lists conventions used throughout this reference Overview Supported FeaturesAccessing User InterfaceCallout # Lines 1 Dual T1/PRI ConfigurationConfiguring Span Interface UI console’s main menuMenu Option 2 Configuring the span line’s line coding Menu Option 1 Configuring the span line’s framing modeFraming mode selects the T1 format This diagram represents this process Menu Option 4 Configuring the span line’s jitter attenuationMenu Option 6 Configuring for the Telco’s switch type Menu Option 7 Configuring the span line’s idle bit patternMenu Option 8 Mapping the span line’s DS0s to chassis modems DS0#sl#/ch#Menu Option 11 Configuring span level call-type blocking Menu Option 9 Configuring the span line’s signaling channelMenu Option 10 Configuring the span line’s interface ID Menu Option 12 Configuring span level cause codesFollowing types of cause codes are supported Menu Option 13 Configuring the DS0 level call-type blockingCause Code Type Default Cause Code Value Description DSS DS0#, DS0#, DS0#-DS0#,... for multiple DS0s Menu Option 14 Configuring the DS0 level service stateMenu Option 15 Configuring the Short Haul NIC line length Any changes made will take effect immediately Routing ConfiguringInbound Call Menu Option 1 Selecting a Gateway to process digital callsConfiguring inbound call routing PHIDX#ph=PH#,ct=xIDP# Use the following syntax to assign a pool type to a pool ID IdptCard Menu Option 1 Saving configuration changes to NvramSaved to Nvram will be restored Menu Option 9 Allowing ISDN-GWC terminationMenu Option 5 Configuring chassis slot devices Menu Option 2 Restoring configuration from NvramMenu Option 3 Restoring the default configuration Menu Option 4 Assigning timing source priorityMenu Option 8 Enabling automatic DS0 state change Menu Option 6 Configuring the modem routing methodMenu Option 7 Configuring the UI console password Configuring Software Fault Event Logging Menu Option 9 Companding Code ConfigurationCommands and logging out of the user interface UI console Dual T1/PRI MaintenanceCommands Dual T1/PRIIssuing this command reboots the NAC Menu Option 1 Resetting the highest priority timing sourceMenu Option 2 Resetting the PRI NAC Selecting option 1 from the main menu produces this screenMenu Options Forcing receiver reframe on the span linesForcing the NAC to master the TDM bus Changing span line service state Menu Option 11 Disabling red Alarm LEDsChanging individual DS0 service states Connect/disconnect B-channel on span lines 1Logging Out Command, from the console’s main menuFeature in the card configuration option of the main menu UI ConsoleDisplays Dual T1/PRI Status DisplaysDual T1/PRI Status From the user interface UI console’s main menuMenu Option 1 Checking power-up self test status RAMMenu Option 2 Checking the T1/PRI’s overall status Menu Option 3 Checking chassis slot device configurationsNo NAC is installed and assigned to that particular slot Menu Option 4 Checking DS0/modem channel status Menu Option 5 Checking the chassis’ Isdn gateway statusChecking span line 1 and 2’s DS0 status NetServer PRI NAC Checking span line 1 and 2’s alarm/event statusTime slot is available and awaiting a call Time slots are mapped toDual T1/PRI Status Displays 8CHAPTER 4 Dual T1/PRI Status Displays Press Ctrl-Rto reset any of the counters on this screen Trouble Clearing Using the LEDsIndicate line signal conditions Trouble clearing informationCD 1 or Alrm 1 or Lpbk 1 or T1 Condition LED Color Alarm Severity ResultLevels Layer 2 D-channel StatusCorrecting Alarm/Error Conditions Alarm/Error Level Trouble ClearingOff and signaling Channel Down Current Draw Technical SpecificationsCertification Regulatory United States ComplianceShipping and Storage Physical DimensionsEnvironment OperatingIndex Certification B-1INDEX-2