3Com T1/PRI Menu Option 11 Disabling red Alarm LEDs, Connect/disconnect B-channel on span lines 1

Page 33

3-4CHAPTER 3: DUAL T1/PRI MAINTENANCE

Menu Option 11 Disabling red ALARM LEDs

Menu Options 12 and 13

Menu Options 14 and 15

Menu Options 16 and 17

The span line ALARM LEDs on the NAC’s front panel remain lit for the duration of an alarm condition. In cases where the alarm condition is recognized and it is determined that the cause for this alarm is accounted for, disable the LED with this option.

An example of such a condition would be when only one span is being used. Since there is no span line physically attached to the NIC’s span 2 port at the time the NAC is installed, the ALARM LED for span 2 goes red. You may wish to disable the LED because this is a normal operating condition.

Connect/disconnect B-channel on span lines 1 and 2

This option allows you to connect and/or disconnect the B-channel on span lines 1 and 2.

Changing individual DS0 service states

This option allows you to place an individual DS0 in or out of service (locally). This is useful for troubleshooting or testing.

Use the following syntax when configuring this option:

SS:DS0# (for a single channel)

SS:DS0#,DS0#,... (for single, non-sequential channels)

SS:DS0#-DS0#(for a range of channels)

Where:

SS= service state (I for in-service, O for local out of service)

DS0# = DS0 number (1–23)

Changing span line service state

This option allows you to place the entire span line (1 and/or 2) in or out of service (locally). This is useful for troubleshooting or testing.

Page 32 Page 34
Image 33
Page 32 Page 34
Contents
Version Number Dual T1/PRIDual T1/PRI 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Configuring the span line’s interface ID Dual T1/PRI Maintenance Trouble Clearing Page Finding Specific About this ReferenceInformation This Reference If you are looking for Turn toConventions This table lists conventions used throughout this referenceIcon Description Accessing Supported FeaturesOverview User InterfaceCallout # Configuring Span Dual T1/PRI ConfigurationLines 1 Interface UI console’s main menuMenu Option 1 Configuring the span line’s framing mode Framing mode selects the T1 formatMenu Option 2 Configuring the span line’s line coding Menu Option 4 Configuring the span line’s jitter attenuation This diagram represents this processMenu Option 7 Configuring the span line’s idle bit pattern Menu Option 6 Configuring for the Telco’s switch typeDS0#sl#/ch# Menu Option 8 Mapping the span line’s DS0s to chassis modemsMenu Option 10 Configuring the span line’s interface ID Menu Option 9 Configuring the span line’s signaling channelMenu Option 11 Configuring span level call-type blocking Menu Option 12 Configuring span level cause codesMenu Option 13 Configuring the DS0 level call-type blocking Cause Code Type Default Cause Code Value DescriptionFollowing types of cause codes are supported Menu Option 14 Configuring the DS0 level service state Menu Option 15 Configuring the Short Haul NIC line lengthDSS DS0#, DS0#, DS0#-DS0#,... for multiple DS0s Any changes made will take effect immediately Inbound Call ConfiguringRouting Menu Option 1 Selecting a Gateway to process digital callsPHIDX#ph=PH#,ct=x Configuring inbound call routingIDP# Idpt Use the following syntax to assign a pool type to a pool IDSaved to Nvram will be restored Menu Option 1 Saving configuration changes to NvramCard Menu Option 9 Allowing ISDN-GWC terminationMenu Option 3 Restoring the default configuration Menu Option 2 Restoring configuration from NvramMenu Option 5 Configuring chassis slot devices Menu Option 4 Assigning timing source priorityMenu Option 6 Configuring the modem routing method Menu Option 7 Configuring the UI console passwordMenu Option 8 Enabling automatic DS0 state change Menu Option 9 Companding Code Configuration Configuring Software Fault Event LoggingCommands Dual T1/PRI MaintenanceCommands and logging out of the user interface UI console Dual T1/PRIMenu Option 2 Resetting the PRI NAC Menu Option 1 Resetting the highest priority timing sourceIssuing this command reboots the NAC Selecting option 1 from the main menu produces this screenForcing receiver reframe on the span lines Forcing the NAC to master the TDM busMenu Options Changing individual DS0 service states Menu Option 11 Disabling red Alarm LEDsChanging span line service state Connect/disconnect B-channel on span lines 1Feature in the card configuration option of the main menu Command, from the console’s main menuLogging Out UI ConsoleDual T1/PRI Status Dual T1/PRI Status DisplaysDisplays From the user interface UI console’s main menuRAM Menu Option 1 Checking power-up self test statusMenu Option 3 Checking chassis slot device configurations No NAC is installed and assigned to that particular slotMenu Option 2 Checking the T1/PRI’s overall status Menu Option 5 Checking the chassis’ Isdn gateway status Menu Option 4 Checking DS0/modem channel statusChecking span line 1 and 2’s DS0 status Time slot is available and awaiting a call Checking span line 1 and 2’s alarm/event statusNetServer PRI NAC Time slots are mapped toDual T1/PRI Status Displays 8CHAPTER 4 Dual T1/PRI Status Displays Press Ctrl-Rto reset any of the counters on this screen Indicate line signal conditions Using the LEDsTrouble Clearing Trouble clearing informationLevels Alarm Severity ResultCD 1 or Alrm 1 or Lpbk 1 or T1 Condition LED Color Layer 2 D-channel StatusAlarm/Error Level Trouble Clearing Correcting Alarm/Error ConditionsOff and signaling Channel Down Certification Technical SpecificationsCurrent Draw Regulatory United States ComplianceEnvironment Physical DimensionsShipping and Storage OperatingCertification B-1 IndexINDEX-2
Related manuals
Manual 52 pages 9.78 Kb