3Com T1/PRI manual Technical Specifications, Certification, Current Draw, Statements

Page 48

B

TECHNICAL SPECIFICATIONS

Certification

EMI/RFI	■	FCC 15A
	■	EN55022 A

Safety	■	UL 1950
	■	C-UL
	■	EN 60950
	■	JATE

Regulatory	United States
Compliance	FCC Part 15 Compliance Statement
Statements	FCC Part 15 Compliance Statement
	This equipment has been tested and found to comply with the limits for a
	Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
	are designed to provide reasonable protection against harmful
	interference when the equipment is operated in a commercial
	environment. This equipment generates, uses, and can radiate radio
	frequency energy and, if not installed and used in accordance with the
	instruction manual, may cause harmful interference to radio
	communications. Operation of this equipment in a residential area is likely
	to cause harmful interference in which case the user will be required to
	correct the interference at his own expense.

Current Draw	+5.2 vDC @ 2.0 A typical maximum

Typical Maximum refers to the maximum current draw under most typical configurations.

Image 48

Contents Dual T1/PRI Version NumberDual T1/PRI 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Configuring the span line’s interface ID Dual T1/PRI Maintenance Trouble Clearing Page About this Reference Finding SpecificInformation This Reference If you are looking for Turn toConventions This table lists conventions used throughout this referenceIcon Description Supported Features AccessingOverview User InterfaceCallout # Dual T1/PRI Configuration Configuring SpanLines 1 Interface UI console’s main menuMenu Option 1 Configuring the span line’s framing mode Framing mode selects the T1 formatMenu Option 2 Configuring the span line’s line coding This diagram represents this process Menu Option 4 Configuring the span line’s jitter attenuationMenu Option 6 Configuring for the Telco’s switch type Menu Option 7 Configuring the span line’s idle bit patternMenu Option 8 Mapping the span line’s DS0s to chassis modems DS0#sl#/ch#Menu Option 9 Configuring the span line’s signaling channel Menu Option 10 Configuring the span line’s interface IDMenu Option 11 Configuring span level call-type blocking Menu Option 12 Configuring span level cause codesMenu Option 13 Configuring the DS0 level call-type blocking Cause Code Type Default Cause Code Value DescriptionFollowing types of cause codes are supported Menu Option 14 Configuring the DS0 level service state Menu Option 15 Configuring the Short Haul NIC line lengthDSS DS0#, DS0#, DS0#-DS0#,... for multiple DS0s Any changes made will take effect immediately Configuring Inbound CallRouting Menu Option 1 Selecting a Gateway to process digital callsConfiguring inbound call routing PHIDX#ph=PH#,ct=xIDP# Use the following syntax to assign a pool type to a pool ID IdptMenu Option 1 Saving configuration changes to Nvram Saved to Nvram will be restoredCard Menu Option 9 Allowing ISDN-GWC terminationMenu Option 2 Restoring configuration from Nvram Menu Option 3 Restoring the default configurationMenu Option 5 Configuring chassis slot devices Menu Option 4 Assigning timing source priorityMenu Option 6 Configuring the modem routing method Menu Option 7 Configuring the UI console passwordMenu Option 8 Enabling automatic DS0 state change Configuring Software Fault Event Logging Menu Option 9 Companding Code ConfigurationDual T1/PRI Maintenance CommandsCommands and logging out of the user interface UI console Dual T1/PRIMenu Option 1 Resetting the highest priority timing source Menu Option 2 Resetting the PRI NACIssuing this command reboots the NAC Selecting option 1 from the main menu produces this screenForcing receiver reframe on the span lines Forcing the NAC to master the TDM busMenu Options Menu Option 11 Disabling red Alarm LEDs Changing individual DS0 service statesChanging span line service state Connect/disconnect B-channel on span lines 1Command, from the console’s main menu Feature in the card configuration option of the main menuLogging Out UI ConsoleDual T1/PRI Status Displays Dual T1/PRI StatusDisplays From the user interface UI console’s main menuMenu Option 1 Checking power-up self test status RAMMenu Option 3 Checking chassis slot device configurations No NAC is installed and assigned to that particular slotMenu Option 2 Checking the T1/PRI’s overall status Menu Option 4 Checking DS0/modem channel status Menu Option 5 Checking the chassis’ Isdn gateway statusChecking span line 1 and 2’s DS0 status Checking span line 1 and 2’s alarm/event status Time slot is available and awaiting a callNetServer PRI NAC Time slots are mapped toDual T1/PRI Status Displays 8CHAPTER 4 Dual T1/PRI Status Displays Press Ctrl-Rto reset any of the counters on this screen Using the LEDs Indicate line signal conditionsTrouble Clearing Trouble clearing informationAlarm Severity Result LevelsCD 1 or Alrm 1 or Lpbk 1 or T1 Condition LED Color Layer 2 D-channel StatusCorrecting Alarm/Error Conditions Alarm/Error Level Trouble ClearingOff and signaling Channel Down Technical Specifications CertificationCurrent Draw Regulatory United States CompliancePhysical Dimensions EnvironmentShipping and Storage OperatingIndex Certification B-1INDEX-2