3Com 3C971-F manual Windows NT Driver Installation

Page 40

3-18 CHAPTER 3: WINDOWS NT DRIVER INSTALLATION

Complete substeps c–f below for enabled clients. Otherwise, go to substep a to select another client or go to step 8 to exit the LEC ATM Adapter configuration.

cSet the MTU Size.

This entry is used by the client to request an MTU (Maximum Transfer Unit) size from the server. The server, in turn, replies with an MTU equal to or less than the requested value. All nodes that are part of the same logical IP subnet must use the same MTU size. Refer to your network documentation to determine the appropriate setting.

A setting of 1514 is recommended for ATM networks that interface with an Ethernet LAN. If ATM nodes are the only end-nodes on the network, a setting of 9K will dramatically improve performance.

dEnter the ELAN Name.

This is the network name of the server that you prefer the client to join. Configuration servers, such as the 3Com Cellplex 7000, require the ELAN name of the LES you want the client to join. Refer to your server documentation to determine the specific requirements.

eSelect the LECS/LES address option.

There are two radio buttons to set the type of client contact at bootup.

LECS option: Contacts the LAN emulation configuration server with the 20-byte address in the ATM Address box. In turn, the LECS supplies the client with all the necessary information to contact the appropriate LAN emulation server (LES).

Image 40
Contents PCI 155 Fiber Network Adapter User GuideLifetime Warranty Sweden, Finland, Norway 3C971-F Atmlink PCI 155 Fiber 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Troubleshooting Page Figures Prompt for Additional Channels About this Guide How to Use This GuideIntroduction Conventions Text DescriptionIntroduction 3C971-F ATMLink PCI AdapterProduct Features Software Drivers 3C971-F Adapter Installation KitPCI Technology Introduction Installation Overview Hardware InstallationTools Required Installing the 3C971-F Adapter Save the screw for later in this sectionInstalling the 3C971-F Adapter Press down gently and firmly on the board to seat it properly 3SC Duplex Connection Turn on the power to the computer Windows NT Driver InstallationOverview Installation Procedures Overview System Requirements Installing the Adapter Device Driver 1Network Settings Screen Select the Add Adapter button. The dialog box in -2 appearsInsert the device driver diskette in a floppy disk drive 3Selecting the Floppy DriveIf needed, change the drive designation Select the OK buttonEdit the PCI adapter parameters Edit the signaling transport items 6Configuring the Signaling Transport7Completed Network Settings Select the OK button on the Network Settings screen Edit the TCP/IP parametersWindows NT Driver Installation Installing the Adapter Device Driver Select Restart Now to reboot the computer Select OK when the TCP/IP Configuration is completeConfiguring the LAN Emulation Clients LECs Set the value in the Interrupt list box 10LEC ConfigurationSelect the Configure button Elan Name blankEdit the LEC ATM Adapter items 11LEC ATM Adapter ConfigurationWindows NT Driver Installation When all clients are configured, select the OK button Select the OK button to exit the LEC Configuration dialog boxSelect OK Exit Windows NT and reboot the computer 12LECS/LES Reboot PromptSelect the Control Panel icon from the Main group Removing a Windows NT DriverSelect the Remove button 14Confirming Adapter and Driver Removal Click the OK button in the Network Settings screen Select the Restart Now button to reboot the computerNetware 4.1 Server Driver Installation Loading the Novell NetWare Server Driver Select Driver options Press Insert to install an unlisted driver 3Select Additional DriverInsert the 3Com 3C971-F driver diskette in a floppy drive 5Notes for Selecting a DrivePress Enter to select the driver Configuring Network ChannelsSelect Yes to copy the driver files to the server Configuring Network Channels 9Configuring TCP/IP Network Interface Edit Channel number 10Change IPX Frame TypeEnter Elan Name Enter the LECS/LES network addressConfiguring Network Channels Select Save parameters and load driver Press Enter to accept the assigned numberDo one of the following 15Prompt for Additional ChannelsEditing the AUTOEXEC.NCF File 17Selecting the NCF Files EditorFrom the system prompt, enter the command Removing a Driver from NetWareSelect NCF files options Troubleshooting Startup ProblemsBootup Problems Applications ProblemsAdapter Problems Specifications HardwareMemory Bus InterfaceNetwork Connections Standards ComplianceEnvironment RangeOn-line Technical Services Access by ModemAccess by Isdn Call the telephone number nearest youLog on to CompuServe Press Return to see the 3ComForum main menuSupport from Your Network Supplier Returning Products for Repair Country Telephone Number Fax NumberGlossary ATM ForumCall control Call setupCell Cell switching Connectionless ATMEnd system HeaderIlmi MbpsPacket switching MulticastMultimode NodeService bit rate SignalingVirtual circuit virtual channel Token ringVirtual path VPI Index NumericsLEC Limited Warranty 3Com Corporation FCC Class a Verification Statement Reader Comment Form 3Com Corporation Business Reply Mail