ADC EMU-830 Network Screen, Logging in to the Main menu To log in to the Main menu, Main Menu

Page 36

Chapter 3: Provisioning

September 25, 2006

Network Screen

Note: The shelf with the > symbol (for example, >Shelf #28 in Figure 3-2) is the local shelf connected to the management station PC. Other shelves without the > symbol are remote shelves connected to the local shelf through an Ethernet subnet.

The Network screen (Figure 3-2) includes the Login command, Upload menu, and Quit command. The Upload menu provides the mechanism to upload image files to local or remote line units or to local or remote EMUs for system management. See “Managing Firmware Through the Upload Menu” on page 3-24to use this command. The Quit command provides a logout from the Network screen.

The Network screen also includes the Shelf ID field and the Alarm Status field. The Shelf ID field initially shows Shelf 1 for all shelves in this subnet until the shelf ID is configured for each shelf (see “Set Shelf ID” on page 3-19for configuring the Shelf ID). The Alarm Status field shows the active alarm status of each shelf in this multishelf network.

 

Figure 3-2. Network Screen

Logging in to the Main menu

 

To log in to the Main menu:

 

 

 

Step

Action

 

 

1In the Network screen, select a shelf from 1 to 32 for which you want to view EMU or Line Unit configuration. Use the Ç and È arrow keys.

2Type the letter L (or press ENTER). The Main menu screen for the selected shelf is displayed (see Figure 3-3 on page 3-5).

Main Menu

Use the Å arrow key to select Main, then press ENTER to display the Main menu screen (Figure 3-3 on page 3-5). The Main menu screen shows the alarm status for a selected shelf and its DSL cards. It also allows you to log into the console menu for any card in the shelf and to disable the card’s alarm reporting functions.

Image 36
Contents WorldDSLTM Exchange Office Management Unit Revision History Table of Contents Table of ContentsSeptember 25 LTPE-UM-3159-02List of Figures 21.Xmodem Transfer Message List of FiguresSeptember 25List of Tables LTPE-UM-3159-02 ViiList of Tables September 25 Viii LTPE-UM-3159-02 Introduction OrganizationIntended Audience ConventionsEU Compliance Inspecting Your ShipmentAbout This Manual September 25 Reader Alert MeaningNEW Features Standard FeaturesName Mode Function Front PanelEMU-830 List 4A and 6A Front Panel Components Major Components Multishelf TAOSeptember 25 Overview Local Management of a Single Shelf Using RS-232/Telnet Multishelf TAO Network Screen Snmp Snmp Management Information Base Ethernet NetworkTraps WorldDSL TrapsTraps Definition Bootp and Tftp Protocols Xmodem ProtocolAlarms Autonomous DIAL-OUT Alarm ReportingExternal Shelf Clock Backup Circuit External Shelf Clock and EMU-830 List 6A Backup CircuitOverview September 25 LTPE-UM-3159-02 EMU Jumper Settings Location of the Slip Header Connector P6 on the EMU-830EMU Installation Installation September 25September 25 Installation Installing the EMU-830 into Slot 17 of EMS-830Multishelf Cable Connections BASE-T Multishelf Cable ConnectionsEMU-830 Console Port Pinouts to DB-9 or DB-25 Connector Local Terminal ConnectionsConsole port Remote Terminal and Local Shelf Modem Connections Local Shelf Modem for Multishelf TAOAT&F Shelf Modem for Slip Operation Modem to EMU Serial Cable PinoutsModem to Slip Port Cable Pinouts Console Menu Navigation Console Menu OptionsConsole Menu Navigation Keys Press this Key To Perform this FunctionProvisioning September 25 Logon, Network, and Main Menu Screen SelectionsScreens and Selections Displays and Functions Multishelf Configuration September 25 ProvisioningLogging On Network Screen Logging in to the Main menu To log in to the Main menuMain Menu Shelf Alarms DSL/G.SHDSL Alarm ReportingHDSL/G.SHDSL Line Unit Status Logging in to an HDSL/G.SHDSL CircuitDSL Line Unit Status Conditions State Indicator Description DSL Circuit Alarms in Order of Severity PriorityLogging into DSL Circuits Enabling or Disabling Alarm Reporting To enable or disable alarm reporting for DSL circuitsConfig Menu Configure Network Parameters for Multishelf TAO and Snmp Configure EMU Autoconfiguration through Bootp Network ParametersOption Function Snmp Parameters Menu Provisioning September 25 Configure Snmp Community Strings Configure Snmp Trap ReceiversConfigure System Identification Snmp Parameters Menu Option FunctionOption Function Modem Parameters Configure and Test Dial-out Alarm Reporting Modem Parameters MenuLOSW* and LOSW1 Alarm Reporting Screen 10. Shelf Alarms Menu Remote Alarm Reporting 11. Remote Alarm Reporting Menu Item Set Date and Time12. Set Date/Time Dialog Box Change Password Provisioning September 25 To set the date and time13. Change Password Dialog Box Set Shelf ID Terminal Settings Provisioning September 25 To set the shelf IDSet to Factory Defaults 16. Restore To Factory Defaults Warning PromptReset EMU Inventory Information ScreenData in Inventory Information Screen Field DescriptionManaging Firmware Through the Upload Menu Upload to a Local or Remote Line UnitScreen -2 on 19. Upload Line Unit Menu Item 21. Xmodem Transfer Message September 25 Provisioning Upload Local EMU 23. Upload EMU Menu Item 25. Tftp Upload EMU Prompt 27. Boot Loader Prompt Upload Remote EMU29. Remote EMU Upload Message Provisioning September 25 LTPE-UM-3159-02 Power Requirements EnvironmentalRegulatory Approvals CompatibilityAppendix a Specifications September 25 LTPE-UM-3159-02 Sales Assistance Systems IntegrationADC Technical Assistance Center 800.366.3891Appendix B Product Support September 25 LTPE-UM-3159-02 Glossary LTPE-UM-3159-02 GL-1Glossary September 25 GL-2 LTPE-UM-3159-02September 25 Glossary LTPE-UM-3159-02 GL-3Glossary September 25 GL-4 LTPE-UM-3159-02 Certification and Warranty World Headquarters For Technical Assistance