ADC Network Unit user manual Mbps Ethernet RJ-45 Connector Pin #, Function, Optical Cables

Page 17

	August 7, 2006				Chapter 2: Installation
		Table 2-1. 10/100 Mbps Ethernet RJ-45 Connector
	Pin #	Signal Name	Function	Pin #	Signal Name	Function

	1	TX+	Transmit Data	2	TX–	Transmit Data

	3	RX+	Receive Data	4	---	Not used

	5	---	Not used	6	RX–	Receive Data

	7	---	Not used	8	---	Not used

		Table 2-2. 1000BaseT Ethernet RJ-45 Connector

	Pin #	Signal Name	Function	Pin #	Signal Name	Function

	1	BD1+	Bidirectional	2	BD1–	Bidirectional

	3	BD2+	Bidirectional	4	BD3+	Bidirectional

	5	BD3–	Bidirectional	6	BD2–	Bidirectional

	7	BD4+	Bidirectional	8	BD4–	Bidirectional

Optical Cables

The maximum cable length is the cable length that the signal can travel without suffering from critical attenuation (degradation).

The maximum distance that any optical link can support is dependent upon attenuation and dispersion at a particular wavelength, maximum bit rate, receiver sensitivity, splice and connector loss, and the data rate used. Refer to SFP specifications for operating parameters.

AIWN-UM-7001-01

2-5

Image 17

Contents Ethernet Network Interface Unit Eniu Revision History Table of Contents Table of Contents August 7 AIWN-UM-7001-01 List of Figures List of Figures August 7 AIWN-UM-7001-01 AIWN-UM-7001-01 Vii List of TablesList of Tables August 7 Viii AIWN-UM-7001-01 Introduction About this ManualOrganization Intended AudienceReader Alert Meaning Inspecting Your ShipmentAbout This Manual August 7 Product Description OverviewOverview August 7 Eniu LED Indicators and ControlsFront Panel Surface Mount Installation InstallationDesktop Installation Ground Connection Power and Ground ConnectionsInstallation August 7 Four-Pin Power Plug Wiring Diagram Eniu Rear View with RJ-45 Connector Power ConnectionCabling Eniu Front View with RJ-45 Connector RJ-45 Ethernet CablesBaseT Ethernet RJ-45 Connector Pin # 100 Mbps Ethernet RJ-45 Connector Pin #Function Optical CablesDB-9 Communications Cable EIA-232 Communication Port DefaultsCLI Command Prompts Effective privilege COMMAND-LINE Interface CLICommand Prompt Commands List Commands OverviewSecurity Initial SET-UPSET Networksubscriber Interface Speed 101001000 Autoforce ConfigurationGET Configuration SET Error Forwarding ON/OFF GET Configuration GET Loopback StatusSET Keep Alive Onoff SET Loopback OnoffSET OAM Configuration OAM ConfigurationSET Echo Onoff Clear System NameSET OAM Mode Activepassiveoff SET Exfo OAM ConfigurationSET Discovery Mode Onoff SET Swap Address Mode OnoffPerformance and Alarms August 7 Provisioning User and Privilege SettingsConfigure Alarm Thresholds Purpose GET UsersGET Network Optical Power GET Subscriber Optical Power GET TemperatureGET Optical Thresholds Clear Performance StatusExit ResetGET Inventory SET LED TestProvisioning August 7 AIWN-UM-7001-01 Specifications Appendix a Specifications August 7 AIWN-UM-7001-01 Product Support Appendix B Product Support August 7 AIWN-UM-7001-01 AIWN-UM-7001-01 GL-1 GlossaryGlossary August 7 GL-2 AIWN-UM-7001-01 Certification and Warranty For Technical Assistance World Headquarters