Adder Technology 1000 manual USB Country Code, Country Code Settings AUTO, MANUAL, Disabled

Page 48

USB Country Code

Some computers query the keyboard to find out its country code and key layout. These computers use this information to configure the way that they interpret the data coming from the keyboard and so it is important for the correct country information to be supplied. Not all keyboards report country information and two different styles of keyboard may be connected to the AdderView CATx 1000.

To get here

1From a local or remote keyboard, log on as a standard (limited options) or ‘admin’ user.

2Press (hotkeys can change).

3Press to select ‘More menus’.

4Press again to select ‘Advanced menus’.

5Highlight the USB Country Code option and press Enter.

6Select ‘Setup Options’.

Country Code

Settings: AUTO, MANUAL, DISABLED

ADDERVIEW CATx 1000

USB Country Code
Country Code	AUTO
Default Country	32

Space-Toggle

-Up -Down Esc-Quit

Default Country

The codes that may be used within this option are as follows:

Country	Code	Country	Code
Arabic	01	Persian (Farsi)	20
Belgian	02	Poland	21
Canadian-Bilingual	03	Portugese	22
Canadian-French	04	Russian	23
Czech Republic	05	Slovakian	24
Danish	06	Spanish	25
Finnish	07	Swedish	26
French	08	Swiss/French	27
German	09	Swiss/German	28
Greek	10	Switzerland	29
Hebrew	11	Taiwan	30
Hungary	12	Turkish-Q	31
International (ISO)	13	UK	32
Italian	14	US	33
Japan (Katakana)	15	Yugoslavia	34
Korean	16	Turkish-F	35
Latin American	17	Reserved	36-255
Netherlands	18	Not supported	00
Norwegian	19

  

In AUTO mode the AdderView CATx 1000 will attempt to query the keyboard attached to the local port to ascertain a country code. If a country code is not found then the AdderView CATx 1000 will use the current value of the Default Country option. In MANUAL mode, the connected local keyboard is not queried for country information and instead the Default Country value is reported to all computers that request country information. In DISABLED mode, no country information is supplied to computers requesting country information.

 



47

Image 48

Contents AdderView CATx Contents Further information Introduction AdderView CATx 1000 features front and rear Remote user portWhat’s in the box What you may additionally needMounting Single unit rack bracketsDouble unit rack brackets CAM Computer Power System Switch ConnectionsLocal user To connect the local user portCable lengths for remote user locations To connect a remote userComputer system via CAM To connect a computer systemPower in connection To connect the power supplyPower control port To connect and address the switch boxesSwitch Cascading multiple units See alsoTips for successful cascading To connect units in cascadeAddressing computers in a cascade Multiple video head connections Slave AdderView CATxRemote switching control Host computer port/channel Video offConfiguration Overall initial configurationConfiguration menus To access the configuration menuGeneral security and configuration steps Configuration menus layoutTo enable general security To set an Admin passwordAccess to all computers Press Access to no computers Press Registering users edit user listTo create/edit user accounts Registering computers edit computer list To create/edit computer entriesVideo compensation Remote user video compensationTo display a suitable high contrast image If the image controls cannot provide a crisp imageRemote user skew adjustment To apply remote user video compensationTo autoset sharpness X100 modules only Press To use skew adjustment Using the supplied skew patternCreating a skew test pattern To select an autoscan mode AutoscanningTo select an autoscan period To define an autoscan listSaving and restoring configuration settings To transfer configuration settingsTo edit the configuration settings Hints for editingWhat to do if the Admin password has been forgotten To clear a password and restore factory default settingsPower switching configuration Power control sequencesTo configure the power sequences for each host computer To control two or more ports simultaneouslyPerforming upgrades Items required to use the upgrade utilityUpgrading AdderView CATx 1000 units and CAMs To use the KVM Firmware Uploader utilityIssues to consider when performing flash upgrades Local and remote user access To gain access as a local or remote userTo select a computer using hotkeys Selecting a computerTo select a computer using the on-screen menu Standard hotkeysSelection Menu here you can select computers by name To select a computer using mouse buttons To select a computer using mouse buttons Advanced methodUser arbitration simultaneous local and remote users Logging in and out Selecting cascaded computersTo log in to the AdderView CATx To log out from the AdderView CATxTo enable/disable the confirmation box To change banner colours or disable the bannerConfirmation box Reminder bannerPower switching via configuration menu To switch a computer on or offUser preferences and functions Getting assistance US +1 888 275Appendix 1 Configuration menus To access the configuration menusFunctions User Preferences Mouse Switching Autoscan ModeGlobal Preferences Screen Saver Settings 1, 2, 3, 5, 10 Seconds User Timeout Settings 1, 2, 5, 10, 30 SECONDS, 1, 5, 10 Minutes OSD Dwell TimeSetup Options DDC Source Settings AUTO, LOCAL, REMOTE, Default DDC Refresh Settings AT START, DisabledAdvanced Options FormatCountry Code Settings AUTO, MANUAL, Disabled Default CountryUSB Country Code Appendix 2 Cable and connector specifications AdderView CATx 1000 to power switch cablePower switch to power switch daisy chain cable Warranty Safety informationRadio Frequency Energy European EMC directive 89/336/EECFCC Compliance Statement United States Canadian Department of Communications RFI statementHoe Huat Industrial Building Index 