ADIC FastStor Mass Storage Device manual Features

Page 19

Features

Multi-function Operator Panel. The Operator Panel, located to the right, under the front door, employs a 1-line by 10- character liquid crystal display (LCD), a four-key keypad, and three LEDs to permit you to monitor and control the operations of your library. Specific areas of the LCD provide you with information such as: status of the tape storage slots (empty, or data cartridge present); which cartridge is loaded into the drive; status of the cartridge in the drive (write-protected or data compression enabled); and inform you when the drive requires cleaning.

Media Transporter. The Media Transporter is the media cartridge handling mechanism and normally responds to commands from the application software to move the cartridges between the storage slots and the drive. Employing a bi-directional, pass-through gripper, the Media Transporter picks and places cartridges to/from the front and rear mounted storage slots.

Scalar Emulation. To maximize application software compatibility, your FastStor shares the same command set as the ADIC Scalar library, and can appear as either a FastStor or a Scalar.

System Integrity. The cartridge storage slots, drive, and robotics are protected by a physically lockable door.

Cleaning Cartridge. Although the cleaning cartridge can occupy a cartridge storage slot in the FastStor (facilitating automated cleaning cycles), manual insertion of a cleaning cartridge is permitted by opening the front door and installing the cleaning cartridge into any unoccupied storage slot. The Operator Panel is then used to load/unload the cleaning cartridge to/from the drive.

Manual Cartridge Use. Individual cartridges can easily be transported to the drive by manually opening the front door and installing the cartridge into any unoccupied storage slot. The Operator Panel is then used to load cartridges to the drive.

Cartridge Pre-Check. Whenever you power up your FastStor it will scan the cartridge storage slots and the drive and build a log of valid cartridge locations.

Reverse Cartridge Protection. The five front cartridge storage slots employ a design that prevents the cartridges from being inserted incorrectly.

Built-in Diagnostics. Your FastStor includes diagnostic firmware that tells you when drive head cleaning is required, reports diagnostic results, and drive operating status.

Barcode Ready. The available barcode reader option delivers instant media verification and inventory.

24 Hour Fast Exchange. In the event your FastStor needs to be serviced, ADIC will provide you with a next day advanced exchange to reduce down time.

Introduction3

Image 19
Contents FastStor Installation Operating GuideCopyright Adic 1997, 1998 Copyright NoticeCopyright 1997 Adic Europe Copyright Notice EuropeFCC Notices USA Only Regulatory NoticesIC Notice Canada Only CE Notice EN 55022 Compliance Czech Republic OnlyVcci Notices Japan Only Declaration of Conformity Precautions Safety NoticesBlank Table of Contents Table of Contents Quick Start Guide LDR Scsi ID 1, DRV Scsi ID Power Button LCD indicates 1-7 loaded Scsi Cable Xvi Quick Start Guide Chapter Equipment Description Features Options DLT DrivesScsi Interface Connectors Switches and IndicatorsFastStor Series Front Panel 3 4 5 6 Rea yMode DLT Data Cartridge DLT MediaScsi Host Adapter Other RequirementsApplication Software Hardware Installation Checking the Accessories Installing the Host AdapterUnpacking and Inspecting FastStor Rear Panel Installing the Scsi Cable and TerminatorConnecting More than One FastStor Installing the Application SoftwarePreparing the Host Computer System Operation and Maintenance Normal Operations Powering on the SystemGeneral Guidelines Rv init Setting the Scsi IDsPower Up Checks InitOperation and Maintenance Prepare and Install the Data Cartridges Close and Lock the Front Door Drive Status MessagesMode FastStor ModesLoa rv Mode 1A Load DRVSRC slot Eject rv Mode 1B Eject DRVEjecting Loa slot Mode 2 Load SlotSRC slot N Eject slot Mode 3 Eject SlotEject pckr Mode 4 Eject PckrSt slot n Ensity Mode 5 DensityFmt Set scsi Mode 6 SET Scsi IDScsi Rv I Rv scsiCycle pwr Cleaning the Drive Head Normal MaintenanceCleaning Tape It means You should Drive Head Cleaning ProcedureCleaning the Enclosure Troubleshooting and Diagnostics Loader and Drive Operational Problems Installation ProblemsSp fw Iag menuSp l r fw Sp rv fw Fw NnnnFp fw Nnnn Sp mtn fwMtn fw NN Sp fp fwSign on Sp T fwCycle Test Chg mo eCycleS Cycle TestCt 2 Sel CleaningRMV 2 Sel AC oN Enabling AutocleanDisabling Autoclean Using AutocleanSP cOUNTS AC OFFFrt pk ct UPG rv fw 000000XXRmv 2 sel Error Message Listing FastStor Error MessagesEnvironmental Considerations When You Call ADIC’S Technical Assistance CenterBlank Appendix Physical