Cisco Systems D200 manual 19-18

Page 18

Chapter 19 DLPs D200 to D299

DLP- D218 Provision SNCP Ring Selectors During Circuit Creation

DLP-D218 Provision SNCP Ring Selectors During Circuit Creation

Purpose

This task provisions subnetwork connection protection (SNCP) ring

 

selectors during circuit creation. Use this task only if the circuit will be

 

routed on an SNCP ring.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 17-49

 

You must have the Circuit Attributes page of the Circuit Creation wizard

 

open.

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

Note Provisioning SD-P or SF-P thresholds on the Circuit Attributes page of the Circuit Creation wizard sets the values only for SNCP-protected spans. The circuit source and destination use the node default values of 10E-4 for SD-P and 10E-6 for SF-P for unprotected circuits and for the source and drop of SNCP circuits.

Step 1 In the SNCP area of the Circuit Attributes page, set the SNCP path selectors:

•Provision working go & return on primary path—Check this box to route the working path on one fiber pair and the protect path on a separate fiber pair. This feature only applies to bidirectional SNCP circuits.

•Revertive—Check this box if you want traffic to revert to the working path when the conditions that diverted it to the protect path are repaired. If you do not choose Revertive, traffic remains on the protect path after the switch.

•Reversion time—If Revertive is checked, click the Reversion time field and choose a reversion time from the drop-down list. The range is 0.5 to 12.0 minutes. The default is 5.0 minutes. This is the amount of time that will elapse before the traffic reverts to the working path. Traffic can revert when conditions causing the switch are cleared.

•SF threshold—For high-order circuits, set the SNCP path-level signal failure (SF) bit error rate (BER) thresholds. Unavailable for low-order circuits.

•SD threshold—For high-order circuits, set the SNCP path-level signal degrade (SD) BER thresholds. Unavailable for low-order circuits.

•Switch on PDI-P—For high-order circuits, check this box if you want traffic to switch when an high-order payload defect indicator (PDI) is received. Unavailable for low-order circuits.

Step 2 Return to your originating procedure (NTP).

 

Cisco ONS 15454 SDH Procedure Guide, R7.2

19-18

October 2007

Page 17 Page 19
Image 18
Page 17 Page 19
Contents DLP-D201 Apply a Lock-On 19-1Required/As Needed DLP-D202 Apply a LockoutPurpose 19-2DLP-D203 Clear a Lock-On or Lockout 19-3DLP-D205 Clean Fiber Connectors with Cletop 19-4Click the Provisioning Server Trails tabs DLP-D206 Clean the Fiber AdaptersDLP-D207 Delete a Server Trail 19-5Click the Provisioning External Alarms tabs DLP-D208 Change External Alarms Using the AIC-I CardDLP-D209 Change External Controls Using the AIC-I Card 19-6DLP-D210 Change AIC-I Card Orderwire Settings 19-7Click the Performance Ether Ports Statistics tabs DLP-D211 Provision CE-1000-4 Ethernet PortsClick the Provisioning Ether Ports tabs 19-8DLP-D212 Create a User Data Channel Circuit Network view, click the Provisioning Overhead Circuits tabs19-9 DLP-D214 Change the Service State for a Port Click the Provisioning Card tabs19-10 DLP-D215 Consolidate Links in Network View 19-111shows a network view with unconsolidated DCC and PPC links 19-1219-13 Consolidated Links in Network ViewDLP-D216 Change the STM-N Card ALS Maintenance Settings 19-14Manual Restart for Test -Manually 19-15DLP-D217 MS-SPRing Exercise Ring Test Click the Provisioning MS-SPRing tabs19-16 19-17 19-18 Security DLP-D219 Provision a Low-Order Tunnel RouteDLP-D220 Provision E-Series Ethernet Ports Click the Provisioning Port tabsClick the Provisioning Vlan tabs 19-20Setting Description 19-21DLP-D222 Provision G-Series Ethernet Ports Click the Performance Statistics tabs19-22 DLP-D223 Download an Alarm Severity Profile 19-23DLP-D224 Adjust the Java Virtual Memory Heap Size Click OK19-24 DLP-D225 Enable Alarm Filtering 19-25DLP-D227 Disable Alarm Filtering DLP-D229 View Circuits on a Span19-26 DLP-D230 Change a Circuit State 19-27DLP-D231 Edit a Circuit Name 19-28DLP-D232 Change Active and Standby Span Color 19-29Click Reset to Defaults DLP-D233 Edit Sncp Circuit Path Selectors19-30 19-31 19-32 Selecting Single Roll Attributes19-33 Selecting a New Endpoint19-34 Viewing the Rolls TabClick Finish 19-3519-36 19-37 10 Selecting Dual Roll Attributes11 Setting Roll Routing Preferences 19-3819-39 Click the Circuits tab 19-4019-41 19-42 19-43 Click the Circuits Rolls tabs DLP-D240 Cancel a RollDLP-D239 Delete a Roll 19-44DLP-D241 Clear an MS-SPRing Manual Ring Switch 19-45DLP-D242 Create an MS-SPRing on a Single Node 19-46DLP-D243 Create a Vlan 19-4719-48 12 Reinitialization Tool19-49 19-50 DLP-D246 Provision E-Series Ethernet Card Mode 19-51Click the Maintenance Protection tabs DLP-D247 Change an STM-N Card19-52 DLP-D249 Provision IP Settings DLP-D248 Delete VLANs19-53 Click the Provisioning Network General tabs 19-5419-55 Active TCC2/TCC2P LEDs Standby TCC2/TCC2P LEDs 19-56Type-ChooseSimple Password DLP-D250 Set Up or Change Open Shortest Path First ProtocolClick the No Authentication button 19-5719-58 DLP-D251 Set Up or Change Routing Information Protocol 19-59DLP-D254 TCC2/TCC2P Card Active/Standby Switch Test 19-60DLP-D255 Cross-Connect Card Side Switch Test 19-61Click the Maintenance Cross-Connect tabs DLP-D256 View Ethernet Statistics PM Parameters19-62 DLP-D257 View Ethernet Utilization PM Parameters Click the Performance Utilization tabs19-63 DLP-D258 View Ethernet History PM Parameters 19-64DLP-D260 Set Auto-Refresh Interval for Displayed PM Counts 19-65DLP-D261 Refresh PM Counts for a Different Port DLP-D262 Filter the Display of Circuits19-66 19-67 19-68 J1 Function Cards 19-6919-70 19-71 DLP-D265 Change the Login Legal Disclaimer 19-72DLP-D266 Change IP Settings 19-73DLP-D268 Apply a Custom Network View Background Map 19-74DLP-D269 Enable Dialog Box Do-Not-Display Option DLP-D271 Change Node Security Policy on a Single Node19-75 19-76 DLP-D272 Change Node Security Policy on Multiple Nodes 19-77DLP-D273 Modify Snmp Trap Destination 19-78DLP-D303 Initiate an MS-SPRing Force Ring Switch task on 19-79Change Card 19-80DLP-D295 Perform a Manual Span Upgrade on an Sncp 19-8119-82 19-83 DLP-D298 Check the Network for Alarms and Conditions 19-84DLP-D299 Initiate an MS-SPRing Span Lockout 19-8519-86

D200 specifications

Cisco Systems has long been a leader in networking technology, and one of its standout products is the Cisco D200. Designed to meet the demands of modern businesses, the D200 is a versatile and robust device that facilitates seamless connectivity and effective network management.

The Cisco D200 is primarily known for its performance and reliability in various deployment scenarios. It is equipped with dual-band Wi-Fi capabilities, supporting both 2.4 GHz and 5 GHz frequencies. This allows users to optimize their wireless network, reducing interference and providing the flexibility to support a wide range of devices in an increasingly wireless world.

One of the standout features of the D200 is its advanced security protocols. Featuring integrated firewalls and support for VPNs, the device ensures that data remains protected against potential cyber threats. With the rise in remote work and digital collaboration, the D200 provides businesses with secure access control, ensuring that sensitive information is safeguarded from unauthorized access.

Another key characteristic of the D200 is its ease of management. With Cisco's user-friendly interface, network administrators can easily configure and monitor the device. The D200 is also compatible with Cisco's DNA Center, enabling businesses to leverage automation and AI-driven insights to optimize their networks and improve operational efficiency.

Performance-wise, the D200 boasts impressive throughput capabilities, making it suitable for high-traffic environments such as offices and educational institutions. Its robust hardware allows for multiple concurrent connections, ensuring that even during peak usage times, network performance remains uninterrupted. Quality of Service (QoS) features also prioritize critical applications, enhancing the overall user experience.

In terms of scalability, the D200 is designed to grow with a business. Whether an organization is expanding its device fleet or increasing bandwidth demands, the D200 can adapt to these changes without compromising performance. Moreover, ongoing firmware updates from Cisco ensure that the device remains current with the latest technologies and security enhancements.

In summary, the Cisco D200 is an essential tool for any business seeking to enhance its networking capabilities. With its advanced features, secure architecture, and ease of management, it stands out as a reliable choice for organizations looking to future-proof their networking infrastructure. As technology continues to evolve, the D200 remains a stalwart in enabling connectivity and efficiency in the digital age.
Top Page Image Contents