Cisco Systems D200 manual DLP-D223 Download an Alarm Severity Profile, 19-23

Page 23

Chapter 19 DLPs D200 to D299

DLP- D223 Download an Alarm Severity Profile

Note Reprovisioning an Ethernet port on the G-Series card does not reset the Ethernet statistics for that port.

Step 6 Return to your originating procedure (NTP).

DLP-D223 Download an Alarm Severity Profile

Purpose

This task downloads a custom alarm severity profile from a network-drive

 

accessible CD-ROM, floppy disk, or hard disk location.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 17-49

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

Step 1 To access the alarm profile editor from network view, click the Provisioning > Alarm Profiles tabs.

Step 2 To access the profile editor from node view, click the Provisioning > Alarm Profiles > Alarm Profile Editor tabs.

Step 3 To access the profile editor from a card view, click the following tabs:

•If the card is an E-Series Ethernet, G-Series Ethernet, STM-N, or electrical (DS3i-N-12, E1-N-14, E1-42, or E3-12) card, click the Provisioning > Alarm Profiles > Alarm Profile Editor tabs.

•If the card is an ML-Series Ethernet (traffic) card, click the Provisioning > Ether Alarming > Alarm Profile Editor tabs if you want to apply the profile to the front physical ports, or the Provisioning > POS Alarming > Alarm Profile Editor tabs if you want to apply the profile to the packet over SDH (POS) ports. For more information about ML-Series card ports and service, refer to the Ethernet Card Software Feature and Configuration Guide for the Cisco ONS 15454, Cisco ONS 15454 SDH, and Cisco ONS 15327.

•If the card is an FC_MR-4 card, click the Provisioning > Alarm Profiles > Alarm Profile Editor tabs.

Step 4 Click Load.

Step 5 If you want to download a profile that exists on the node, click From Node in the Load Profile(s) dialog box.

a.Click the node name you are logged into in the Node Names list.

b.Click the name of the profile in the Profile Names list, such as Default.

Step 6 If you want to download a profile that is stored locally or on a network drive, click From File in the Load Profile(s) dialog box.

a.Click Browse.

b.Navigate to the file location in the Open dialog box.

c.Click Open.

 

 

Cisco ONS 15454 SDH Procedure Guide, R7.2

 

 

 

 

 

 

October 2007

 

 

19-23

 

 

 

 

 

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 19-1 DLP-D201 Apply a Lock-On19-2 DLP-D202 Apply a LockoutPurpose Required/As Needed19-3 DLP-D203 Clear a Lock-On or Lockout19-4 DLP-D205 Clean Fiber Connectors with Cletop19-5 DLP-D206 Clean the Fiber AdaptersDLP-D207 Delete a Server Trail Click the Provisioning Server Trails tabs19-6 DLP-D208 Change External Alarms Using the AIC-I CardDLP-D209 Change External Controls Using the AIC-I Card Click the Provisioning External Alarms tabs19-7 DLP-D210 Change AIC-I Card Orderwire Settings19-8 DLP-D211 Provision CE-1000-4 Ethernet PortsClick the Provisioning Ether Ports tabs Click the Performance Ether Ports Statistics tabs19-9 DLP-D212 Create a User Data Channel CircuitNetwork view, click the Provisioning Overhead Circuits tabs 19-10 DLP-D214 Change the Service State for a PortClick the Provisioning Card tabs 19-11 DLP-D215 Consolidate Links in Network View19-12 1shows a network view with unconsolidated DCC and PPC linksConsolidated Links in Network View 19-1319-14 DLP-D216 Change the STM-N Card ALS Maintenance Settings19-15 Manual Restart for Test -Manually19-16 DLP-D217 MS-SPRing Exercise Ring TestClick the Provisioning MS-SPRing tabs 19-17 19-18 Click the Provisioning Port tabs DLP-D219 Provision a Low-Order Tunnel RouteDLP-D220 Provision E-Series Ethernet Ports Security19-20 Click the Provisioning Vlan tabs19-21 Setting Description19-22 DLP-D222 Provision G-Series Ethernet PortsClick the Performance Statistics tabs 19-23 DLP-D223 Download an Alarm Severity Profile19-24 DLP-D224 Adjust the Java Virtual Memory Heap SizeClick OK 19-25 DLP-D225 Enable Alarm Filtering19-26 DLP-D227 Disable Alarm FilteringDLP-D229 View Circuits on a Span 19-27 DLP-D230 Change a Circuit State19-28 DLP-D231 Edit a Circuit Name19-29 DLP-D232 Change Active and Standby Span Color19-30 Click Reset to DefaultsDLP-D233 Edit Sncp Circuit Path Selectors 19-31 Selecting Single Roll Attributes 19-32Selecting a New Endpoint 19-33Viewing the Rolls Tab 19-3419-35 Click Finish19-36 10 Selecting Dual Roll Attributes 19-3719-38 11 Setting Roll Routing Preferences19-39 19-40 Click the Circuits tab19-41 19-42 19-43 19-44 DLP-D240 Cancel a RollDLP-D239 Delete a Roll Click the Circuits Rolls tabs19-45 DLP-D241 Clear an MS-SPRing Manual Ring Switch19-46 DLP-D242 Create an MS-SPRing on a Single Node19-47 DLP-D243 Create a Vlan12 Reinitialization Tool 19-4819-49 19-50 19-51 DLP-D246 Provision E-Series Ethernet Card Mode19-52 Click the Maintenance Protection tabsDLP-D247 Change an STM-N Card 19-53 DLP-D249 Provision IP SettingsDLP-D248 Delete VLANs 19-54 Click the Provisioning Network General tabs19-55 19-56 Active TCC2/TCC2P LEDs Standby TCC2/TCC2P LEDs19-57 DLP-D250 Set Up or Change Open Shortest Path First ProtocolClick the No Authentication button Type-ChooseSimple Password19-58 19-59 DLP-D251 Set Up or Change Routing Information Protocol19-60 DLP-D254 TCC2/TCC2P Card Active/Standby Switch Test19-61 DLP-D255 Cross-Connect Card Side Switch Test19-62 Click the Maintenance Cross-Connect tabsDLP-D256 View Ethernet Statistics PM Parameters 19-63 DLP-D257 View Ethernet Utilization PM ParametersClick the Performance Utilization tabs 19-64 DLP-D258 View Ethernet History PM Parameters19-65 DLP-D260 Set Auto-Refresh Interval for Displayed PM Counts19-66 DLP-D261 Refresh PM Counts for a Different PortDLP-D262 Filter the Display of Circuits 19-67 19-68 19-69 J1 Function Cards19-70 19-71 19-72 DLP-D265 Change the Login Legal Disclaimer19-73 DLP-D266 Change IP Settings19-74 DLP-D268 Apply a Custom Network View Background Map19-75 DLP-D269 Enable Dialog Box Do-Not-Display OptionDLP-D271 Change Node Security Policy on a Single Node 19-76 19-77 DLP-D272 Change Node Security Policy on Multiple Nodes19-78 DLP-D273 Modify Snmp Trap Destination19-79 DLP-D303 Initiate an MS-SPRing Force Ring Switch task on19-80 Change Card19-81 DLP-D295 Perform a Manual Span Upgrade on an Sncp19-82 19-83 19-84 DLP-D298 Check the Network for Alarms and Conditions19-85 DLP-D299 Initiate an MS-SPRing Span Lockout19-86

D200 specifications

Cisco Systems has long been a leader in networking technology, and one of its standout products is the Cisco D200. Designed to meet the demands of modern businesses, the D200 is a versatile and robust device that facilitates seamless connectivity and effective network management.

The Cisco D200 is primarily known for its performance and reliability in various deployment scenarios. It is equipped with dual-band Wi-Fi capabilities, supporting both 2.4 GHz and 5 GHz frequencies. This allows users to optimize their wireless network, reducing interference and providing the flexibility to support a wide range of devices in an increasingly wireless world.

One of the standout features of the D200 is its advanced security protocols. Featuring integrated firewalls and support for VPNs, the device ensures that data remains protected against potential cyber threats. With the rise in remote work and digital collaboration, the D200 provides businesses with secure access control, ensuring that sensitive information is safeguarded from unauthorized access.

Another key characteristic of the D200 is its ease of management. With Cisco's user-friendly interface, network administrators can easily configure and monitor the device. The D200 is also compatible with Cisco's DNA Center, enabling businesses to leverage automation and AI-driven insights to optimize their networks and improve operational efficiency.

Performance-wise, the D200 boasts impressive throughput capabilities, making it suitable for high-traffic environments such as offices and educational institutions. Its robust hardware allows for multiple concurrent connections, ensuring that even during peak usage times, network performance remains uninterrupted. Quality of Service (QoS) features also prioritize critical applications, enhancing the overall user experience.

In terms of scalability, the D200 is designed to grow with a business. Whether an organization is expanding its device fleet or increasing bandwidth demands, the D200 can adapt to these changes without compromising performance. Moreover, ongoing firmware updates from Cisco ensure that the device remains current with the latest technologies and security enhancements.

In summary, the Cisco D200 is an essential tool for any business seeking to enhance its networking capabilities. With its advanced features, secure architecture, and ease of management, it stands out as a reliable choice for organizations looking to future-proof their networking infrastructure. As technology continues to evolve, the D200 remains a stalwart in enabling connectivity and efficiency in the digital age.
Top Page Image Contents