Cisco Systems D200 manual DLP-D246 Provision E-Series Ethernet Card Mode, 19-51

Page 51

Chapter 19 DLPs D200 to D299

DLP- D246 Provision E-Series Ethernet Card Mode

Step 5 Click Go.

Caution Before continuing with the next step, verify that the database to upload is correct. You cannot reverse the upload process after you click Yes.

Step 6 Review the information on the Confirm NE Re-Initialization dialog box, then click Yes to start the reinitialization.

The reinitialization begins. After the software is downloaded and activated and the database is uploaded to the TCC2/TCC2P cards, “Complete” appears in the status bar and the TCC2/TCC2P cards reboot. Wait a few minutes for the reboot to complete.

Step 7 After the reboot is complete, log into the node using the “DLP-D60 Log into CTC” task on page 17-49.

Step 8 Complete the “NTP-D81 Change Node Management Information” procedure on page 11-2and the “NTP-D201 Change CTC Network Access” procedure on page 11-2for information on provisioning the node name, IP address, subnet mask and gateway, and IIOP port.

Step 9 Return to your originating procedure (NTP).

DLP-D246 Provision E-Series Ethernet Card Mode

 

 

 

 

Purpose

This task provisions an E-Series Ethernet card for Multicard EtherSwitch

 

 

 

 

 

Group, Single-card EtherSwitch, or Port-mapped mode.

 

 

 

 

Tools/Equipment

E-Series Ethernet cards must be installed.

 

 

 

 

Prerequisite Procedures

DLP-D60 Log into CTC, page 17-49

 

 

 

 

Required/As Needed

As needed

 

 

 

 

Onsite/Remote

Onsite or remote

 

 

 

 

Security Level

Provisioning or higher

 

 

 

 

 

 

 

Caution

You cannot change the mode while the Ethernet card is carrying circuits. If you want change the card

 

 

 

 

mode, delete any circuits that it carries first. See the “NTP-D288 Modify and Delete Overhead Circuits

 

 

 

 

and Server Trails” procedure on page 7-4.

 

 

 

 

 

 

 

 

 

 

Step 1

In network view, double-click the node containing the E-Series Ethernet card that you want to provision,

 

 

 

 

then double-click the Ethernet card.

 

 

Step 2

Click the Provisioning > Card tabs.

 

 

Step 3

In the Card Mode area, choose one of the following:

 

 

 

 

• For multicard EtherSwitch circuit groups, choose Multicard EtherSwitch Group.

 

 

 

 

• For single-card EtherSwitch circuits, choose Single-card EtherSwitch.

 

 

 

 

• For port-mapped circuits, choose Port-mapped.

 

 

Step 4

Click Apply.

 

 

 

 

 

 

Step 5

If you are using multicard EtherSwitch circuits, repeat Steps 2 through 4 for all other Ethernet cards in

 

 

 

 

the node that will carry the multicard EtherSwitch circuits.

 

 

 

 

 

Cisco ONS 15454 SDH Procedure Guide, R7.2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

October 2007

 

 

 

19-51

 

 

 

 

 

 

Page 50 Page 52
Image 51
Page 50 Page 52
Contents 19-1 DLP-D201 Apply a Lock-On19-2 DLP-D202 Apply a LockoutPurpose Required/As Needed19-3 DLP-D203 Clear a Lock-On or Lockout19-4 DLP-D205 Clean Fiber Connectors with Cletop19-5 DLP-D206 Clean the Fiber AdaptersDLP-D207 Delete a Server Trail Click the Provisioning Server Trails tabs19-6 DLP-D208 Change External Alarms Using the AIC-I CardDLP-D209 Change External Controls Using the AIC-I Card Click the Provisioning External Alarms tabs19-7 DLP-D210 Change AIC-I Card Orderwire Settings19-8 DLP-D211 Provision CE-1000-4 Ethernet PortsClick the Provisioning Ether Ports tabs Click the Performance Ether Ports Statistics tabsDLP-D212 Create a User Data Channel Circuit Network view, click the Provisioning Overhead Circuits tabs19-9 DLP-D214 Change the Service State for a Port Click the Provisioning Card tabs19-10 19-11 DLP-D215 Consolidate Links in Network View19-12 1shows a network view with unconsolidated DCC and PPC linksConsolidated Links in Network View 19-1319-14 DLP-D216 Change the STM-N Card ALS Maintenance Settings19-15 Manual Restart for Test -ManuallyDLP-D217 MS-SPRing Exercise Ring Test Click the Provisioning MS-SPRing tabs19-16 19-17 19-18 Click the Provisioning Port tabs DLP-D219 Provision a Low-Order Tunnel RouteDLP-D220 Provision E-Series Ethernet Ports Security19-20 Click the Provisioning Vlan tabs19-21 Setting DescriptionDLP-D222 Provision G-Series Ethernet Ports Click the Performance Statistics tabs19-22 19-23 DLP-D223 Download an Alarm Severity ProfileDLP-D224 Adjust the Java Virtual Memory Heap Size Click OK19-24 19-25 DLP-D225 Enable Alarm FilteringDLP-D227 Disable Alarm Filtering DLP-D229 View Circuits on a Span19-26 19-27 DLP-D230 Change a Circuit State19-28 DLP-D231 Edit a Circuit Name19-29 DLP-D232 Change Active and Standby Span ColorClick Reset to Defaults DLP-D233 Edit Sncp Circuit Path Selectors19-30 19-31 Selecting Single Roll Attributes 19-32Selecting a New Endpoint 19-33Viewing the Rolls Tab 19-3419-35 Click Finish19-36 10 Selecting Dual Roll Attributes 19-3719-38 11 Setting Roll Routing Preferences19-39 19-40 Click the Circuits tab19-41 19-42 19-43 19-44 DLP-D240 Cancel a RollDLP-D239 Delete a Roll Click the Circuits Rolls tabs19-45 DLP-D241 Clear an MS-SPRing Manual Ring Switch19-46 DLP-D242 Create an MS-SPRing on a Single Node19-47 DLP-D243 Create a Vlan12 Reinitialization Tool 19-4819-49 19-50 19-51 DLP-D246 Provision E-Series Ethernet Card ModeClick the Maintenance Protection tabs DLP-D247 Change an STM-N Card19-52 DLP-D249 Provision IP Settings DLP-D248 Delete VLANs19-53 19-54 Click the Provisioning Network General tabs19-55 19-56 Active TCC2/TCC2P LEDs Standby TCC2/TCC2P LEDs19-57 DLP-D250 Set Up or Change Open Shortest Path First ProtocolClick the No Authentication button Type-ChooseSimple Password19-58 19-59 DLP-D251 Set Up or Change Routing Information Protocol19-60 DLP-D254 TCC2/TCC2P Card Active/Standby Switch Test19-61 DLP-D255 Cross-Connect Card Side Switch TestClick the Maintenance Cross-Connect tabs DLP-D256 View Ethernet Statistics PM Parameters19-62 DLP-D257 View Ethernet Utilization PM Parameters Click the Performance Utilization tabs19-63 19-64 DLP-D258 View Ethernet History PM Parameters19-65 DLP-D260 Set Auto-Refresh Interval for Displayed PM CountsDLP-D261 Refresh PM Counts for a Different Port DLP-D262 Filter the Display of Circuits19-66 19-67 19-68 19-69 J1 Function Cards19-70 19-71 19-72 DLP-D265 Change the Login Legal Disclaimer19-73 DLP-D266 Change IP Settings19-74 DLP-D268 Apply a Custom Network View Background MapDLP-D269 Enable Dialog Box Do-Not-Display Option DLP-D271 Change Node Security Policy on a Single Node19-75 19-76 19-77 DLP-D272 Change Node Security Policy on Multiple Nodes19-78 DLP-D273 Modify Snmp Trap Destination19-79 DLP-D303 Initiate an MS-SPRing Force Ring Switch task on19-80 Change Card19-81 DLP-D295 Perform a Manual Span Upgrade on an Sncp19-82 19-83 19-84 DLP-D298 Check the Network for Alarms and Conditions19-85 DLP-D299 Initiate an MS-SPRing Span Lockout19-86

D200 specifications

Cisco Systems has long been a leader in networking technology, and one of its standout products is the Cisco D200. Designed to meet the demands of modern businesses, the D200 is a versatile and robust device that facilitates seamless connectivity and effective network management.

The Cisco D200 is primarily known for its performance and reliability in various deployment scenarios. It is equipped with dual-band Wi-Fi capabilities, supporting both 2.4 GHz and 5 GHz frequencies. This allows users to optimize their wireless network, reducing interference and providing the flexibility to support a wide range of devices in an increasingly wireless world.

One of the standout features of the D200 is its advanced security protocols. Featuring integrated firewalls and support for VPNs, the device ensures that data remains protected against potential cyber threats. With the rise in remote work and digital collaboration, the D200 provides businesses with secure access control, ensuring that sensitive information is safeguarded from unauthorized access.

Another key characteristic of the D200 is its ease of management. With Cisco's user-friendly interface, network administrators can easily configure and monitor the device. The D200 is also compatible with Cisco's DNA Center, enabling businesses to leverage automation and AI-driven insights to optimize their networks and improve operational efficiency.

Performance-wise, the D200 boasts impressive throughput capabilities, making it suitable for high-traffic environments such as offices and educational institutions. Its robust hardware allows for multiple concurrent connections, ensuring that even during peak usage times, network performance remains uninterrupted. Quality of Service (QoS) features also prioritize critical applications, enhancing the overall user experience.

In terms of scalability, the D200 is designed to grow with a business. Whether an organization is expanding its device fleet or increasing bandwidth demands, the D200 can adapt to these changes without compromising performance. Moreover, ongoing firmware updates from Cisco ensure that the device remains current with the latest technologies and security enhancements.

In summary, the Cisco D200 is an essential tool for any business seeking to enhance its networking capabilities. With its advanced features, secure architecture, and ease of management, it stands out as a reliable choice for organizations looking to future-proof their networking infrastructure. As technology continues to evolve, the D200 remains a stalwart in enabling connectivity and efficiency in the digital age.
Top Page Image Contents