Cisco Systems D200 manual DLP-D255 Cross-Connect Card Side Switch Test, 19-61

Page 61

Chapter 19 DLPs D200 to D299

DLP- D255 Cross-Connect Card Side Switch Test

Step 9 After the node icon turns green (within 1 to 2 minutes), double-click it. On the shelf graphic, observe the following:

•The previous standby TCC2/TCC2P card has a green ACT LED.

•The previous active TCC2/TCC2P card LEDs go through the following LED sequence: NP (card not present), Ldg (software is loading), amber SBY LED (TCC2/TCC2P card is in standby mode). The LEDs should complete this sequence within 5 to 10 minutes.

Step 10 Verify that traffic on the test set connected to the node is still running. If a traffic interruption occurs, do not continue, refer to your next level of support.

Step 11 Repeat Steps 2 through 10 to return the active/standby TCC2/TCC2P cards to their configuration at the start of the procedure.

Step 12 Verify that the TCC2/TCC2P cards appear as noted in Step 5.

Step 13 Return to your originating procedure (NTP).

DLP-D255 Cross-Connect Card Side Switch Test

Purpose

This task verifies that the XC-VXL-10G, and XC-VXL-2.5G, or

 

XC-VXC-10G cards can effectively switch service (active to standby and

 

standby to active).

Tools/Equipment

The test set specified by the acceptance test procedure, connected and

 

configured as specified in the acceptance test procedure.

Prerequisite Procedures

DLP-D60 Log into CTC, page 17-49

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

Provisioning or higher

Caution Always wait 60 seconds between cross-connect card (side) switches to allow the system to stabilize. This is applicable to all the types of side switches (soft reset or manual switch using CTC or TL1). This condition is also applicable to all the cross-connect types (XC-10G / XC-VXC-10G / XC-VXL-2.5G / XC-VXL-10G / XC-VT).

Step 1 From the View menu, choose Go to Network View.

Step 2 Click the Alarms tab.

a.Verify that the alarm filter is not on. See the “DLP-D227 Disable Alarm Filtering” task on page 19-26as necessary.

b.Verify that no unexplained alarms appear on the network. If unexplained alarms appear, resolve them before continuing. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide if necessary.

Step 3 Click the Conditions tab. Verify that no unexplained conditions appear on the network. If unexplained conditions appear, resolve them before continuing. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide if necessary.

Step 4 On the network map, double-click the node containing the cross-connect cards that you are testing to open it in node view.

 

 

Cisco ONS 15454 SDH Procedure Guide, R7.2

 

 

 

 

 

 

October 2007

 

 

19-61

 

 

 

 

 

Page 60 Page 62
Image 61
Page 60 Page 62
Contents 19-1 DLP-D201 Apply a Lock-OnPurpose DLP-D202 Apply a LockoutRequired/As Needed 19-219-3 DLP-D203 Clear a Lock-On or Lockout19-4 DLP-D205 Clean Fiber Connectors with CletopDLP-D207 Delete a Server Trail DLP-D206 Clean the Fiber AdaptersClick the Provisioning Server Trails tabs 19-5DLP-D209 Change External Controls Using the AIC-I Card DLP-D208 Change External Alarms Using the AIC-I CardClick the Provisioning External Alarms tabs 19-619-7 DLP-D210 Change AIC-I Card Orderwire SettingsClick the Provisioning Ether Ports tabs DLP-D211 Provision CE-1000-4 Ethernet PortsClick the Performance Ether Ports Statistics tabs 19-8Network view, click the Provisioning Overhead Circuits tabs DLP-D212 Create a User Data Channel Circuit19-9 Click the Provisioning Card tabs DLP-D214 Change the Service State for a Port19-10 19-11 DLP-D215 Consolidate Links in Network View19-12 1shows a network view with unconsolidated DCC and PPC linksConsolidated Links in Network View 19-1319-14 DLP-D216 Change the STM-N Card ALS Maintenance Settings19-15 Manual Restart for Test -ManuallyClick the Provisioning MS-SPRing tabs DLP-D217 MS-SPRing Exercise Ring Test19-16 19-17 19-18 DLP-D220 Provision E-Series Ethernet Ports DLP-D219 Provision a Low-Order Tunnel RouteSecurity Click the Provisioning Port tabs19-20 Click the Provisioning Vlan tabs19-21 Setting DescriptionClick the Performance Statistics tabs DLP-D222 Provision G-Series Ethernet Ports19-22 19-23 DLP-D223 Download an Alarm Severity ProfileClick OK DLP-D224 Adjust the Java Virtual Memory Heap Size19-24 19-25 DLP-D225 Enable Alarm FilteringDLP-D229 View Circuits on a Span DLP-D227 Disable Alarm Filtering19-26 19-27 DLP-D230 Change a Circuit State19-28 DLP-D231 Edit a Circuit Name19-29 DLP-D232 Change Active and Standby Span ColorDLP-D233 Edit Sncp Circuit Path Selectors Click Reset to Defaults19-30 19-31 Selecting Single Roll Attributes 19-32Selecting a New Endpoint 19-33Viewing the Rolls Tab 19-3419-35 Click Finish19-36 10 Selecting Dual Roll Attributes 19-3719-38 11 Setting Roll Routing Preferences19-39 19-40 Click the Circuits tab19-41 19-42 19-43 DLP-D239 Delete a Roll DLP-D240 Cancel a RollClick the Circuits Rolls tabs 19-4419-45 DLP-D241 Clear an MS-SPRing Manual Ring Switch19-46 DLP-D242 Create an MS-SPRing on a Single Node19-47 DLP-D243 Create a Vlan12 Reinitialization Tool 19-4819-49 19-50 19-51 DLP-D246 Provision E-Series Ethernet Card ModeDLP-D247 Change an STM-N Card Click the Maintenance Protection tabs19-52 DLP-D248 Delete VLANs DLP-D249 Provision IP Settings19-53 19-54 Click the Provisioning Network General tabs19-55 19-56 Active TCC2/TCC2P LEDs Standby TCC2/TCC2P LEDsClick the No Authentication button DLP-D250 Set Up or Change Open Shortest Path First ProtocolType-ChooseSimple Password 19-5719-58 19-59 DLP-D251 Set Up or Change Routing Information Protocol19-60 DLP-D254 TCC2/TCC2P Card Active/Standby Switch Test19-61 DLP-D255 Cross-Connect Card Side Switch TestDLP-D256 View Ethernet Statistics PM Parameters Click the Maintenance Cross-Connect tabs19-62 Click the Performance Utilization tabs DLP-D257 View Ethernet Utilization PM Parameters19-63 19-64 DLP-D258 View Ethernet History PM Parameters19-65 DLP-D260 Set Auto-Refresh Interval for Displayed PM CountsDLP-D262 Filter the Display of Circuits DLP-D261 Refresh PM Counts for a Different Port19-66 19-67 19-68 19-69 J1 Function Cards19-70 19-71 19-72 DLP-D265 Change the Login Legal Disclaimer19-73 DLP-D266 Change IP Settings19-74 DLP-D268 Apply a Custom Network View Background MapDLP-D271 Change Node Security Policy on a Single Node DLP-D269 Enable Dialog Box Do-Not-Display Option19-75 19-76 19-77 DLP-D272 Change Node Security Policy on Multiple Nodes19-78 DLP-D273 Modify Snmp Trap Destination19-79 DLP-D303 Initiate an MS-SPRing Force Ring Switch task on19-80 Change Card19-81 DLP-D295 Perform a Manual Span Upgrade on an Sncp19-82 19-83 19-84 DLP-D298 Check the Network for Alarms and Conditions19-85 DLP-D299 Initiate an MS-SPRing Span Lockout19-86

D200 specifications

Cisco Systems has long been a leader in networking technology, and one of its standout products is the Cisco D200. Designed to meet the demands of modern businesses, the D200 is a versatile and robust device that facilitates seamless connectivity and effective network management.

The Cisco D200 is primarily known for its performance and reliability in various deployment scenarios. It is equipped with dual-band Wi-Fi capabilities, supporting both 2.4 GHz and 5 GHz frequencies. This allows users to optimize their wireless network, reducing interference and providing the flexibility to support a wide range of devices in an increasingly wireless world.

One of the standout features of the D200 is its advanced security protocols. Featuring integrated firewalls and support for VPNs, the device ensures that data remains protected against potential cyber threats. With the rise in remote work and digital collaboration, the D200 provides businesses with secure access control, ensuring that sensitive information is safeguarded from unauthorized access.

Another key characteristic of the D200 is its ease of management. With Cisco's user-friendly interface, network administrators can easily configure and monitor the device. The D200 is also compatible with Cisco's DNA Center, enabling businesses to leverage automation and AI-driven insights to optimize their networks and improve operational efficiency.

Performance-wise, the D200 boasts impressive throughput capabilities, making it suitable for high-traffic environments such as offices and educational institutions. Its robust hardware allows for multiple concurrent connections, ensuring that even during peak usage times, network performance remains uninterrupted. Quality of Service (QoS) features also prioritize critical applications, enhancing the overall user experience.

In terms of scalability, the D200 is designed to grow with a business. Whether an organization is expanding its device fleet or increasing bandwidth demands, the D200 can adapt to these changes without compromising performance. Moreover, ongoing firmware updates from Cisco ensure that the device remains current with the latest technologies and security enhancements.

In summary, the Cisco D200 is an essential tool for any business seeking to enhance its networking capabilities. With its advanced features, secure architecture, and ease of management, it stands out as a reliable choice for organizations looking to future-proof their networking infrastructure. As technology continues to evolve, the D200 remains a stalwart in enabling connectivity and efficiency in the digital age.
Top Page Image Contents