Cisco Systems D200 manual DLP-D211 Provision CE-1000-4 Ethernet Ports, 19-8

Page 8

Chapter 19 DLPs D200 to D299

DLP- D211 Provision CE-1000-4 Ethernet Ports

DLP-D211 Provision CE-1000-4 Ethernet Ports

Purpose

This task provisions CE-1000-4 Ethernet ports to carry traffic.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 17-49

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

Note You can provision SONET contiguous concatenated (CCAT) or virtual concatenated (VCAT) circuits for the CE-1000-4 before or after provisioning the card’s Ethernet ports and/or packet-over-SDH (POS) ports. See the “NTP-D323 Create an Automatically Routed High-Order Circuit” procedure on page 6-55or the “NTP-D283 Create an Automatically Routed VCAT Circuit” procedure on page 6-97, as needed.

Step 1 In node view, double-click the CE-1000-4 card graphic to open the card.

Step 2 Click the Provisioning > Ether Ports tabs.

Step 3 For each CE-1000-4 port, provision the following parameters:

•Port Name—If you want to label the port, enter the port name.

•Admin State—Select the service state for the port. See the “DLP-D214 Change the Service State for a Port” task on page 19-10for more information.

•Flow Control—Select the flow control for the port. Possible values are None, Symmetrical, and Pass Through.

•Auto Negotiation—Click this check box to enable autonegotiation on the port (default). If you do not want to enable autonegotiation control, uncheck the box.

•MTU—If you want to permit the acceptance of jumbo size Ethernet frames, choose 10004 (default). If you do not want to permit jumbo size Ethernet frames, choose 1548.

•Watermark—Select the flow control watermark for the port. To provision the Low Latency flow control watermark, choose Low Latency from the drop-down list. The Flow Ctrl Lo and Flow Ctrl Hi values change. To provision a Custom flow control watermark, choose Custom from the drop-down list.

Enter values in the Flow Ctrl Hi and Flow Ctrl Lo columns. The Flow Ctrl Lo value has a valid range from 1 to 510 and the Flow Ctrl Hi value has a valid range from 2 to 511. The Flow Ctrl Lo value must be lower than the Flow Ctrl Hi value.

Step 4 Click Apply.

Step 5 Refresh the Ethernet statistics:

a.Click the Performance > Ether Ports > Statistics tabs.

b.Click Refresh.

 

Cisco ONS 15454 SDH Procedure Guide, R7.2

19-8

October 2007

Page 7 Page 9
Image 8
Page 7 Page 9
Contents DLP-D201 Apply a Lock-On 19-1DLP-D202 Apply a Lockout PurposeRequired/As Needed 19-2DLP-D203 Clear a Lock-On or Lockout 19-3DLP-D205 Clean Fiber Connectors with Cletop 19-4DLP-D206 Clean the Fiber Adapters DLP-D207 Delete a Server TrailClick the Provisioning Server Trails tabs 19-5DLP-D208 Change External Alarms Using the AIC-I Card DLP-D209 Change External Controls Using the AIC-I CardClick the Provisioning External Alarms tabs 19-6DLP-D210 Change AIC-I Card Orderwire Settings 19-7DLP-D211 Provision CE-1000-4 Ethernet Ports Click the Provisioning Ether Ports tabsClick the Performance Ether Ports Statistics tabs 19-819-9 DLP-D212 Create a User Data Channel CircuitNetwork view, click the Provisioning Overhead Circuits tabs 19-10 DLP-D214 Change the Service State for a PortClick the Provisioning Card tabs DLP-D215 Consolidate Links in Network View 19-111shows a network view with unconsolidated DCC and PPC links 19-1219-13 Consolidated Links in Network ViewDLP-D216 Change the STM-N Card ALS Maintenance Settings 19-14Manual Restart for Test -Manually 19-1519-16 DLP-D217 MS-SPRing Exercise Ring TestClick the Provisioning MS-SPRing tabs 19-17 19-18 DLP-D219 Provision a Low-Order Tunnel Route DLP-D220 Provision E-Series Ethernet PortsSecurity Click the Provisioning Port tabsClick the Provisioning Vlan tabs 19-20Setting Description 19-2119-22 DLP-D222 Provision G-Series Ethernet PortsClick the Performance Statistics tabs DLP-D223 Download an Alarm Severity Profile 19-2319-24 DLP-D224 Adjust the Java Virtual Memory Heap SizeClick OK DLP-D225 Enable Alarm Filtering 19-2519-26 DLP-D227 Disable Alarm FilteringDLP-D229 View Circuits on a Span DLP-D230 Change a Circuit State 19-27DLP-D231 Edit a Circuit Name 19-28DLP-D232 Change Active and Standby Span Color 19-2919-30 Click Reset to DefaultsDLP-D233 Edit Sncp Circuit Path Selectors 19-31 19-32 Selecting Single Roll Attributes19-33 Selecting a New Endpoint19-34 Viewing the Rolls TabClick Finish 19-3519-36 19-37 10 Selecting Dual Roll Attributes11 Setting Roll Routing Preferences 19-3819-39 Click the Circuits tab 19-4019-41 19-42 19-43 DLP-D240 Cancel a Roll DLP-D239 Delete a RollClick the Circuits Rolls tabs 19-44DLP-D241 Clear an MS-SPRing Manual Ring Switch 19-45DLP-D242 Create an MS-SPRing on a Single Node 19-46DLP-D243 Create a Vlan 19-4719-48 12 Reinitialization Tool19-49 19-50 DLP-D246 Provision E-Series Ethernet Card Mode 19-5119-52 Click the Maintenance Protection tabsDLP-D247 Change an STM-N Card 19-53 DLP-D249 Provision IP SettingsDLP-D248 Delete VLANs Click the Provisioning Network General tabs 19-5419-55 Active TCC2/TCC2P LEDs Standby TCC2/TCC2P LEDs 19-56DLP-D250 Set Up or Change Open Shortest Path First Protocol Click the No Authentication buttonType-ChooseSimple Password 19-5719-58 DLP-D251 Set Up or Change Routing Information Protocol 19-59DLP-D254 TCC2/TCC2P Card Active/Standby Switch Test 19-60DLP-D255 Cross-Connect Card Side Switch Test 19-6119-62 Click the Maintenance Cross-Connect tabsDLP-D256 View Ethernet Statistics PM Parameters 19-63 DLP-D257 View Ethernet Utilization PM ParametersClick the Performance Utilization tabs DLP-D258 View Ethernet History PM Parameters 19-64DLP-D260 Set Auto-Refresh Interval for Displayed PM Counts 19-6519-66 DLP-D261 Refresh PM Counts for a Different PortDLP-D262 Filter the Display of Circuits 19-67 19-68 J1 Function Cards 19-6919-70 19-71 DLP-D265 Change the Login Legal Disclaimer 19-72DLP-D266 Change IP Settings 19-73DLP-D268 Apply a Custom Network View Background Map 19-7419-75 DLP-D269 Enable Dialog Box Do-Not-Display OptionDLP-D271 Change Node Security Policy on a Single Node 19-76 DLP-D272 Change Node Security Policy on Multiple Nodes 19-77DLP-D273 Modify Snmp Trap Destination 19-78DLP-D303 Initiate an MS-SPRing Force Ring Switch task on 19-79Change Card 19-80DLP-D295 Perform a Manual Span Upgrade on an Sncp 19-8119-82 19-83 DLP-D298 Check the Network for Alarms and Conditions 19-84DLP-D299 Initiate an MS-SPRing Span Lockout 19-8519-86

D200 specifications

Cisco Systems has long been a leader in networking technology, and one of its standout products is the Cisco D200. Designed to meet the demands of modern businesses, the D200 is a versatile and robust device that facilitates seamless connectivity and effective network management.

The Cisco D200 is primarily known for its performance and reliability in various deployment scenarios. It is equipped with dual-band Wi-Fi capabilities, supporting both 2.4 GHz and 5 GHz frequencies. This allows users to optimize their wireless network, reducing interference and providing the flexibility to support a wide range of devices in an increasingly wireless world.

One of the standout features of the D200 is its advanced security protocols. Featuring integrated firewalls and support for VPNs, the device ensures that data remains protected against potential cyber threats. With the rise in remote work and digital collaboration, the D200 provides businesses with secure access control, ensuring that sensitive information is safeguarded from unauthorized access.

Another key characteristic of the D200 is its ease of management. With Cisco's user-friendly interface, network administrators can easily configure and monitor the device. The D200 is also compatible with Cisco's DNA Center, enabling businesses to leverage automation and AI-driven insights to optimize their networks and improve operational efficiency.

Performance-wise, the D200 boasts impressive throughput capabilities, making it suitable for high-traffic environments such as offices and educational institutions. Its robust hardware allows for multiple concurrent connections, ensuring that even during peak usage times, network performance remains uninterrupted. Quality of Service (QoS) features also prioritize critical applications, enhancing the overall user experience.

In terms of scalability, the D200 is designed to grow with a business. Whether an organization is expanding its device fleet or increasing bandwidth demands, the D200 can adapt to these changes without compromising performance. Moreover, ongoing firmware updates from Cisco ensure that the device remains current with the latest technologies and security enhancements.

In summary, the Cisco D200 is an essential tool for any business seeking to enhance its networking capabilities. With its advanced features, secure architecture, and ease of management, it stands out as a reliable choice for organizations looking to future-proof their networking infrastructure. As technology continues to evolve, the D200 remains a stalwart in enabling connectivity and efficiency in the digital age.
Top Page Image Contents