Samsung SP-L220 Installation and Connection, Menu and Remote Control, Screen and External Source

Page 31

Before Contacting Service Personnel

Installation and Connection

Symptoms

Troubleshooting

No Power.

I want to install my projector on the ceiling.

External Source can not be selected.

zCheck the power cable connections.

zThe ceiling installation support is sold separately. Contact your local product distributor.

zBe sure that the connection cable(s) (video) is properly connected to the proper port. If the device is not connected properly, it can not be selected.

Menu and Remote Control

Symptoms

Troubleshooting

Remote control does not work.

zCheck whether your remote control is at a right angle and at the correct distance. Remove any obstacles between your remote control and the product.

zDirect lighting of 3-way light bulbs or other lighting device on the remote sensor of the projector may affect the sensitivity and cause the remote control to malfunction.

zCheck if the remote control battery is empty.

zCheck whether the LED indicator on the top of the projector is turned on.

I cannot select a menu.

z Check if the menu is displayed in gray. A gray-colored menu is unavailable.

Screen and External Source

 

Symptoms

Troubleshooting

Cannot see picture images.

z Be sure that the power cord of the projector is connected.

zBe sure that the proper input source is selected.

zCheck that the connectors are properly connected to the ports at the back of the projector.

zCheck the Remote Control batteries.

zBe sure that the <Color>, <Brightness> settings are not at their lower limit.

Poor color.

z Adjust the <Tint> and <Contrast>.

Images are not clear.

z Adjust the focus.

 

z Check that the projection distance is either too far or too near to the screen.

Strange noise.

z If the strange sound continues, contact our service center.

The operating LED is lit up.

z Refer to Corrective Actions According to LED Indications.

Lines appear on the screen.

z Because noise may occur when using your PC, adjust the frequency of the screen.

No external device screen is displayed.

z Check the operating status for the external device and check whether the

 

adjustment items, such as the Brightness and the Contrast have been changed

 

correctly in the <Mode> command screen of the Projector menu.

Only blue screen appears.

z Be sure to properly connect the external devices. Check the connection cables

 

again.

Screen is black and white or abnormal

z As mentioned above, check the adjustment items such as the Brightness, Contrast

color/ screen is too dark or bright.

and Color in the menu.

 

z If you want to restore various settings to their factory defaults, run <Factory

Image 31
Contents Page Do not plug multiple devices into a single wall outlet Insert the power plug firmly so that it does not come looseDo not use loose power outlets or damaged power cables Under no circumstances touch the power plug with wet handsKeep the power cord away from heaters Unplug the power plug before cleaning the productOperable Do not disassemble, or attempt to fix or modify the product Place the product on the ground carefullyDo not drop the product while carrying it Keep the product out of children’s reachThere is a danger of fire or explosion Correct disposal of batteries in this product Europe only Make sure to place your remote control on a table or deskPage Front/Upper Side An optical engine adopting new LCD technologyUnpacking Lens coverLED Indications Clearing Indicator ProblemsRemote Control Signal Receiver Menu PowerMove VOL MuteReturn ExitIBM AV Timing VIDEO/S-VIDEO AV Timing D-Sub Format Resolution ScanZoom and Focus Adjustment Installing the ProjectorSelect Menu Setup Install Rear-Floor Select Menu Setup Install Front-FloorScreen Size and Projection Distance Leveling with Adjustable FeetScreen Connecting a PC using a D-Sub cable Resolution/Size Modes tableConnecting an External Monitor Connecting an AV device with component output Connecting an AV device using a D-Sub cableConnecting an External Speaker Connecting using a Video/S-Video cablePage Turning off the projector Turning on the projectorSelecting an input source Presentation Mode StandardMovie Mode DVD Combo Satellite STB 11 PC AV ReceiverColor Temperature Offset Gain Timing signalAuto Adjustment Coarse Fine Reset Logo Blue Black ResetUsage Color PC menu Sharpness,Tint Zoom Sound Language Menu OptionTransparency Low Medium High OpaqueOff 10 min 20 min 30 min Menu and Remote Control Installation and ConnectionScreen and External Source Defaultfrom the menu Lamp Replacement To clean the exterior and lens of the projectorClean the projector using a soft, dry cloth To clean the interior of the projectorReplacing and Cleaning the Filter Lamp Replacement ProcedurePrecautions when replacing the projector filter Location of the ventilation openings Ventilating openingsCIS Asia Pacific