Samsung SRP-500 manual Changing the DIP switch setting

Page 14

Transmission	2-7	2-8
2400 baud	ON	ON
4800 baud	OFF	ON
9600 baud	OFF	OFF
19200 baud	ON	OFF

*1) : It may use in dark area. (like a restaurant). But printing speed to be slow down.

*2) : Enalbe = Automatically print NV bit image #1 after cutting.

*3) : EPSON Kitchen Printer mode : A alarm is generated by printer after auto-cutting and in paper-end error. (It needs buzzer accessory)

Notice

Changes in DIP switch settings are recognized only when the printer power is turned on or when the printer is reset by using the interface. If the DIP switch setting is changed after the printer power is turned on, the change does not take effect until the printer is turned on again or is reset.

19

3-2. Changing the DIP switch setting

If you need to change settings, follow the steps below to make your changes.

CAUTION

Turn off the printer before removing the DIP switch cover to prevent an electric short, which can damage the printer.

1)Make sure the printer is turned off.

2)Remove the screw from the DIP switch cover.

Then take off the DIP switch cover, which is shown in the illustration below.

3)Set the switches using a pointed tool, such as tweezers or a small screwdriver.

4)Replace the DIP switch cover. Then secure it with the screw.

*The new settings take effect when you turn on the printer.

20

Image 14

Contents SRP-500 Do not let water or other foreign objects Printer ReachTaking following measures EMC and Safety standards Applied Table of contents Introduction Front view Rear viewChoosing a place for the printer Setting up the printerUnpacking Connecting the interface cable Connecting the cablesConnect the AC adapter according to the following procedure Installing or replacing paper roll Installing new Ink cartridges Error LED Using the control panelControl panel Power LED Clean ButtonRunning the self test TroubleshootingSelf test If any of the lights are on, please check the followingYou want to check the operation of the printer by itself Cleaning the print headPrinter stops printing Printing is poorDIP switch functions DIP switch settingsSetting the DIP switches You want to check a software programChanging the DIP switch setting Code table 3 PC860 Portuguese 4 PC 863 Canadian French 5 PC 865 Nordic 16 CP1252 WinLatin1 17 PC 866 Russian 18 CP 852 DosLatin2 19 PC 858 Euro 21 MS-DOS 862 Israel 22 MS-DOS 864 Arabic 23 MS-DOS 874 Thai Control commands list CommandsName Horizontal tab Format Command descriptionsCharacter Code Tables = 2 Off-line status DLE EOT nName Real-time status transmission Format ESC SP n = 3 Error statusDLE ENQ n Name Real-time request to printer FormatESC % n Name Select/cancel user-defined character set FormatESC ! n Name Select print modes FormatName Define user-defined characters Format ESC & y c1 c2 x1 d1...dy x x1... xk d1... dy x xkESC * m nL nH d1...dk ESC = n ESC nESC 3 n ESC ? n ESC D n1... nk NULESC J n ESC E nESC G n ESC U n ESC R nESC a n Name Select paper sensorsto stop printing Format ASCll ESC c 3 nESC c 4 n ESC g0 k nH nL kd1…dmk ESC c 5 nESC d n ESC t n ESC mESC p m t1 t2 Name Transmit paper sensor status Format Name Turns on/off upside-down printing mode FormatESC GS a pL pH n m GS I nGS a n Name Enable/Disable Automatic Status Back Format① GS V m ② GS V m n Second byte printer information Default n = ReferenceFirst byte printer information Third byte paper sensor informationGS j n Status BInk cartridge specification Printing specificationPaper specification Reference informationOptional features Electrical characteristicsDimensions & Weight ReliabilityMemo ………..………………………………………………