Samsung BN68-01416D-00 user manual Switching Your Television On and Off, Viewing the Menus

Page 9

Installing Batteries in the Remote Control

1Lift the cover at the back of the remote control upward as shown in the figure.

2 Install two AAA size batteries.

➢Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.

Do not mix battery types, i.e. alkaline and manganese.

3Close the cover as shown in the figure.

➢Remove the batteries and store them in a cool and dry

place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the batteries last for about one year.)

➢If the remote control doesn’t work! Check the following:

1.Is the TV power on?

2.Are the plus and minus ends of the batteries reversed?

3.Are the batteries drained?

4.Is there a power cut, or is the power cord unplugged?

5.Is there a special fluorescent light or a neon sign nearby?

Switching Your Television On and Off

The main lead is attached to the rear of the television.

1Plug the main lead into an appropriate socket.

➢ The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

2 Press the (Power) button (On/Off) on the front of the television or press the POWER button on the remote control to switch the television on. The programme that you were watching last is re-selected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.

➢If the television is initially powered on, several basic customer settings proceed automatically. Refer to “Plug & Play Feature” on page 10.

3

To switch the television off, press the

 

(Power) button (On/Off) on the front of the television or press

 

 

 

the POWER button on the remote control.

4

To switch the TV on, press the

 

(Power) button (On/Off) on the front of the TV or press the POWER

 

 

 

button or number buttons on the remote control.

Viewing the Menus

1Press the MENU button.

The main menu is displayed on the screen.

Its left side has six icons: Picture, Sound, Channel, Setup, Input, and Digital Menu.

2Press the ▲ or ▼ button to select one of the icons.

Press the ENTER button to access the icon’s sub-menu.

3Press the ▲ or ▼ button to move to items in the menu.

Press the ENTER button to enter items in the menu.

4Press the ▲/▼/◄/► button to change the selected items.

Press the RETURN button to return to the previous menu.

5Press the EXIT button to exit from the menu.

T V

Picture

 

Mode

: Standard

►

Cell Light

 



Contrast

 

5

Brightness

 

45

Sharpness

 

50

Colour

G50

50

Tint

R50

Detailed Settings

►

Picture Options

►

Reset

: OK

►

Move

Enter

Exit

English - 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Country Customer Care Centre  Web Site Contact Samsung Worldwide0818 717 Samsung BN68-01416D-00User Instructions Contents Ferrite Core Power Cord, S-Video Using the Stand-BaseChecking Parts Sold SeparatelyRemote Control Sensor Power IndicatorControl Panel Front or Side PanelInput/Output Specification Connection PanelEXT 1, EXT Hdmi in 1,2 Headphones jackSide Panel Supported modes for HDMI/DVI and ComponentTeletext Functions Viewing the Remote ControlInstalling Batteries in the Remote Control Switching Your Television On and OffViewing the Menus Main lead is attached to the rear of the televisionPlug & Play Feature Make sure that the antenna is connected to the TVPress the Enter button Spain Only If you want to reset this feature …Viewing External Signal Sources Using the Tools ButtonEditing Device Names Not available in DTV or external input modeStoring Channels Automatically You can give a name to the external sourceStoring Channels Manually Channel mode Colour System Auto/PAL/SECAM/NTSC4.43  Sound System BG/DK/I/L Adding channels Adding / Locking ChannelsAdded  Locking channelsAssigning Names to Channels Sorting the Stored ChannelsLNA Low Noise Amplifier Fine Tuning Channel ReceptionEasy Setting Customizing the Picture SettingsPress the or button until you reach the optimal setting Changing the Picture StandardConfiguring Detailed Settings on the Picture Picture Options Bar Patterns, without using an additional Blue Filter Using this function, you can adjust the Colour and Tint toSide to side Horizontal Dot. The Time setting allows − Pixel Shift Using this function, you can minutely moveResetting the Picture Settings to the Factory Defaults You can set detailed picture settingsOptimum condition for pixel shift TV/Ext/AV/Component Sound Features Selecting the Sound Mode depending on the model Connecting Headphones Sold separatelyThis function is only available in Analog TV mode Press the Tools button on the remote control Time FeaturesPress the or button to select Sleep Timer  Timer 1 / Timer 2 / Timer Language Press the or button to select Setup, then press Light Effect Off/In Standby/In Watching TV/Always  Melody Off/Low/Medium/HighSetting up Your PC Software Based on Windows XP Input Mode PC Sub InputHDMI/DVI Input  Auto Adjustment Setting the PCImage Reset Coarse/FinePreviewing the DTV Menu System Language Displaying Programme InformationAudio Language Primary Audio LanguageDigital Channel Operating the DTV Menu − Channel − FrequencyChannel list  Add Preview  DeleteChannels and all channels Channel ListRefer to Next channel listScheduled List Default GuideLanguage All Channels and Favorite ChannelsLanguage, Subtitle Language, and the Teletext Preference The Audio Language, Subtitle Language, Teletext Language of the Language menu show aMenu Transparency This menu consists of 11 sub-menusYou can set the translucency of the on-screen menu Change PIN / Parental LockActivates even though Hard of hearing mode is Subtitle button on the remote controlDigital Text  Press the or button to select required menu− Signal Information − Installing the CI CardYou can get information about the signal status Error level / Signal StrengthFactory state What is Anynet+? Connecting Anynet+ DevicesTo connect to Home Theatre Scanning and Switching between Anynet+ Devices Setting Up Anynet+Meassage Configuring Anynet+ connection... is Turned OffRecording Listening through a Receiver Check Points before Requesting Service# cancel Teletext Feature depending on the modelStore SizeContents Quantity Wall Mount Kit Specifications VesaOr button to select Setup, then press the Enter button Wall- mount adjustment Sold separatelyEntering the menu Remembering the PositionMoving to the remembered position How to assemble the Stand-Base depending on the modelTroubleshooting Specifications Risk of Electric Shock do not Open United Kingdom This page is intentionally Left blank Correct Disposal of This Product
Top Page Image Contents