Mitsubishi Electronics AJ65SBT-64AD user manual Remote Register, Remote register allocation

Page 28

3SPECIFICATION

3.6 Remote Register

MELSEC-A

The AJ65SBT-64AD has a remote resister for data communication with the master module. The remote register allocation and data structures are described.

3.6.1 Remote register allocation

The remote register allocation is shown in Table 3.6.

Table 3.6 Remote register allocation

	Communication direction		Address	Description	Default value	Reference section
			RWwm	A/D conversion enable/prohibit specification	0	Section 3.6.2
	Master	Remote	RWwm+1	Input range setting	0	Section 3.6.3
	Master	Remote	RWwm+2	Moving average processing count setting	0	Section 3.6.4
			RWwm+2	Moving average processing count setting	0	Section 3.6.4
			RWwm+3	Reserved	0	——
			RWrn	CH.1 digital output value	0
	Remote	Master	RWrn+1	CH.2 digital output value	0	Section 3.6.5
	Remote	Master	RWrn+2	CH.3 digital output value	0	Section 3.6.5
			RWrn+2	CH.3 digital output value	0
			RWrn+3	CH.4 digital output value	0

m, n: Address allocated to the master module by the station number setting.

POINT

Do not read or write data from or to the reserved area of the remote register. If data is read or written, we cannot guarantee the functions of the AJ65SBT-64AD.

3 - 13

Image 28

Contents User,s Manual Safety Precautions Installation Precautions Starting and Maintenance Precautions Revisions Manual number is given on the bottom left of the back coverOverview Setup and Preparation Before Operation Programming Procedure Program ExamplesModel Code IB-6672113J872 IB-66251Gppw Product components This product consists of the following Memo Overview MELSEC-A MELSEC-A System Configuration Overall ConfigurationApplicable master modules Applicable SystemRestrictions on use of CC-Link dedicated instructions Specification General SpecificationPerformance Specification I/O Conversion Characteristics Voltage input characteristics Voltage Input Characteristic0mA Current input characteristics4mA Resolution AccuracyCurrent Input Characteristic Accuracy Conversion speed Function List AJ65SBT-64AD function listSampling processing Moving average processingSampling time 4000 2000 Stored second time Stored third time Remote I/O signal list Remote I/O Signals Remote I/O Signals List Functions of the remote I/O signals Remote I/O Signal Details 1/2Remote I/O Signal Details 2/2 Device No Signal Name RXn+1AInitial data setting request Flag RYn+1A Error reset request flagRemote Register Remote register allocation2 A/D conversion enable/prohibit specification Address RWwm Input range setting Address RWwm+1 B15 B12 b11 B8 b7 B4 b3 CH.4 CH.3 CH.2 CH.1Moving average processing count setting Address RWwm+2 5 CH. Digital output value Address RWrn to RWrn+3B15 B14 B13 B12 B11 B10 CH.4 CH.3 CH.2 CH.1 TimesMELSEC-A Setup and Preparation Before Operation Pre-Operation ProcedurePrecautions When Handling Create a program When making offset/gain setting, set allDIN rail DIN rail hook Name of Each Part Setting switches Set Value Setting Switches Transmission SpeedSpeed setting SwitchesOffset/Gain Setting StartPoint Station Number Setting Facing Direction of the Module InstallationData Link Cable Wiring WiringWiring precautions Instructions for handling the CC-Link dedicated cablesMaintenance and Inspection Module connection exampleFor voltage input For current inputMemo Programming Procedure MELSEC-A ProgrammingProgram Examples Program example for power-on MELSEC-A Program example for initial data changing MELSEC-A Initial settings Program example for power-on Setting of automatic refresh parameters Checking Program example for initial data changing MELSEC-A Program examples for use of the QnACPU Automatic refresh parameter setting Program example for initial data changing Program examples for use of the Qcpu Q mode Program for power-on Setting results Setting results of 1 to 8 are shown below Program for initial data changing Troubleshooting Using the Remote Input Signals to Check ErrorsError flag RXnC has turned on Error status flagUsing the LED Indications to Check Errors Set the voltage value to within the range 20.4 toSpecified value? 26.4V To enter the test mode? Terminals acrossOperation? Power on againIf the L ERR. LED has begun flickering though When the digital output value cannot be read Revise the parameter settings Is the L RUN LED lit? Appendix AJ65SBT-64AD AJ65BT-64ADMELSEC-A Appendix2 External dimension diagram Memo Ind ERR.LED of the master station flickers Memo Warranty User,s Manual