4SETUP AND PREPARATION BEFORE OPERATION
4.3 Name of Each Part
MELSEC-A
The name of each part in the AJ65SBT-64AD is shown.
2-piece (CC-Link communication section)
|
| 1) |
|
| 2) |
|
|
| 3) |
|
| 4) |
|
|
|
| 5) |
| |||
PW | RUN L RUN L ERR. CH1 2 | 3 | 4 | OFFSET GAIN |
|
|
|
|
| STATION | NO. |
| B | RATE |
| ||||||
|
|
| SELECT | 40 20 10 | 8 | 4 | 2 | 1 | 4 | 2 | 1 | ON | |||||||||
|
|
|
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| MITSUBISHI |
|
|
|
|
| SET |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| CH1 |
| CH2 |
| CH3 |
|
|
|
| CH4 |
|
|
|
| ||||
DA | DG +24V | 24G |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
| TEST | V+ | I+ |
| V+ | I+ | COM |
| SLD | COM |
| AG |
| |||||||
| DB | SLD | (FG) |
|
|
|
|
|
| ||||||||||||
|
|
| TEST COM | SLD | COM |
| V+ | I+ |
| V+ |
| I+ |
| (FG1) | |||||||
|
|
|
|
|
|
|
| 6) |
| 7) |
|
|
|
|
|
|
|
|
|
|
|
[Terminal numbers and signal names]
1 | 3 | 5 | 7 | 8 | 10 | 12 | 14 | 16 | 18 | 20 | 22 | 24 |
DA | DG |
| +24V |
| 24G |
|
| TEST | V+ | I+ | V+ | I+ | COM | SLD | COM |
| AG | ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2 |
| 4 |
|
| 6 |
|
|
|
|
|
| 9 |
| 11 |
| 13 |
| 15 |
| 17 |
| 19 |
| 21 |
| 23 |
|
| 25 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| DB |
|
| SLD | (FG) |
|
|
|
| TEST |
| COM |
| SLD |
| COM |
| V+ |
|
| I+ |
| V+ |
| I+ |
| FG1 |
Number | Name and |
|
|
|
| Description | |
appearance |
|
|
|
| |||
|
|
|
|
|
| ||
|
| PW LED | ON : Power supply on |
| |||
|
| OFF: Power supply off |
| ||||
|
|
|
| ||||
|
|
|
|
| On | : Normal operation | |
|
|
| Normal mode | Flashing : 0.1s intervals indicate an input range setting error. | |||
|
|
| Off | : 24VDC power supply shutoff or watchdog timer error | |||
|
|
|
|
| |||
|
|
|
|
|
| occurred. | |
|
|
|
|
| On | : Indicates that the SELECT/SET switch is in the SET | |
|
| RUN LED |
|
|
| position. | |
|
|
|
| Flashing : 0.1s intervals indicate that the input range setting is not | |||
|
|
|
|
| |||
|
|
| Test mode |
| any of "user range settings 1 to 3". | ||
|
|
|
| 0.5s intervals indicate that you attempted to make | |||
|
|
|
|
|
| ||
1) | Operation status |
|
|
|
| offset/gain setting outside the setting range. | |
display LED |
|
|
| Off | : Indicates that the SELECT/SET switch is in the | ||
|
|
|
| ||||
|
|
|
|
|
| SELECT or center position. | |
|
| L RUN LED | On | : Normal communication | |||
|
| Off | : Communication cutoff (time expiration error) | ||||
|
|
| |||||
|
|
| On | : Indicates that transmission speed setting or station number setting is | |||
|
|
|
| outside the range. | |||
|
|
| Flicker at fixed intervals | : Indicates that transmission speed setting or station | |||
|
| L ERR. LED |
|
|
| number setting was changed from that at | |
|
| Flicker at unfixed intervals | : Indicates that you forgot fitting the termination resistor or | ||||
|
|
| |||||
|
|
|
|
|
| the module or | |
|
|
|
|
|
| noise. | |
|
|
| Off | : Indicates normal communications. | |||
| Offset/gain | CH | Normal mode | Normally OFF. | |||
2) | OFFSET |
|
| The LEDs lit change every time the SELECT/SET switch is moved | |||
adjusting LEDs | Test mode | ||||||
| GAIN | to SELECT. (Refer to Section 4.4.) | |||||
|
|
|
| ||||
3) | SELECT/SET | Used to make offset/gain setting in the test mode. | |||||
switch | |||||||
|
|
|
|
|
|
4 - 3