Mitsubishi Electronics AJ65SBT-64AD user manual User,s Manual

Page 74

Analog-Digital Converter Module type AJ65SBT-64AD

User,s Manual

MODEL

MODEL

CODE

AJ65S-64AD-U-S-E

13JR18

SH(NA)-080106-A(0010)MEE

HEAD OFFICE : MITSUBISHI DENKI BLDG MARUNOUCHI TOKYO 100-8310 TELEX : J24532 CABLE MELCO TOKYO

NAGOYA WORKS : 1-14 , YADA-MINAMI 5 , HIGASHI-KU, NAGOYA , JAPAN

When exported from Japan, this manual does not require application to the

Ministry of International Trade and Industry for service transaction permission.

Specifications subject to change without notice.

Image 74

Contents User,s Manual Safety Precautions Installation Precautions Starting and Maintenance Precautions Revisions Manual number is given on the bottom left of the back coverOverview Setup and Preparation Before Operation Programming Procedure Program Examples13J872 Model CodeIB-66721 IB-66251Gppw Product components This product consists of the following Memo Overview MELSEC-A MELSEC-A System Configuration Overall ConfigurationRestrictions on use of CC-Link dedicated instructions Applicable SystemApplicable master modules Specification General SpecificationPerformance Specification I/O Conversion Characteristics Voltage input characteristics Voltage Input Characteristic4mA Current input characteristics0mA Resolution AccuracyCurrent Input Characteristic Accuracy Conversion speed Function List AJ65SBT-64AD function listSampling time 4000 2000 Sampling processingMoving average processing Stored second time Stored third timeRemote I/O Signals List Remote I/O SignalsRemote I/O signal list Functions of the remote I/O signals Remote I/O Signal Details 1/2Initial data setting request Remote I/O Signal Details 2/2Device No Signal Name RXn+1A Flag RYn+1A Error reset request flagRemote Register Remote register allocation2 A/D conversion enable/prohibit specification Address RWwm Input range setting Address RWwm+1 B15 B12 b11 B8 b7 B4 b3 CH.4 CH.3 CH.2 CH.1B15 B14 B13 B12 B11 B10 CH.4 CH.3 CH.2 CH.1 Moving average processing count setting Address RWwm+25 CH. Digital output value Address RWrn to RWrn+3 TimesPrecautions When Handling MELSEC-A Setup and Preparation Before OperationPre-Operation Procedure Create a program When making offset/gain setting, set allDIN rail DIN rail hook Name of Each Part Speed setting Setting switchesSet Value Setting Switches Transmission Speed SwitchesOffset/Gain Setting StartPoint Station Number Setting Facing Direction of the Module InstallationWiring precautions Data Link Cable WiringWiring Instructions for handling the CC-Link dedicated cablesFor voltage input Maintenance and InspectionModule connection example For current inputMemo Programming Procedure MELSEC-A ProgrammingProgram Examples Program example for power-on MELSEC-A Program example for initial data changing MELSEC-A Initial settings Program example for power-on Setting of automatic refresh parameters Checking Program example for initial data changing MELSEC-A Program examples for use of the QnACPU Automatic refresh parameter setting Program example for initial data changing Program examples for use of the Qcpu Q mode Program for power-on Setting results Setting results of 1 to 8 are shown below Program for initial data changing Error flag RXnC has turned on TroubleshootingUsing the Remote Input Signals to Check Errors Error status flagSpecified value? 26.4V Using the LED Indications to Check ErrorsSet the voltage value to within the range 20.4 to To enter the test mode? Terminals acrossIf the L ERR. LED has begun flickering though Power on againOperation? When the digital output value cannot be read Revise the parameter settings Is the L RUN LED lit? Appendix AJ65SBT-64AD AJ65BT-64ADMELSEC-A Appendix2 External dimension diagram Memo Ind ERR.LED of the master station flickers Memo Warranty User,s Manual