Hyundai P224WK manual Digital Signage, Set up Value

Page 34

Set up Value

DIGITAL SIGNAGE

Set up Value

installation item	Product 1	Product 2	Product 3	Product 4	Product 5	Product 6
H Set Count	3	3	3	3	3	3
V Set Count	2	2	2	2	2	2
Display Sequence	1	2	3	4	5	6
H Edge ADJ /	These are the set up value to make up the un-displayed area of Bezel Part.
V Edge ADJ	It can be adjustable according to the contents
SET ID	It is necessary to control via RS232 communication port on PC. But do not
SET ID	need to set up or change when they are not controlled by PC
	need to set up or change when they are not controlled by PC
Master	You are recommended to use the Master on state only one of products that
Master	you are using
	you are using

[Cautions]

-In case of connecting the products in series from the input device (HDMI, analog RGB, component, video etc.), up to about 25 units are possible. But, the number of connecting devices can be different from the input signal level of each device and thereby amplified distributor can be needed for this product.

(when over 25 units are connected, the screen may not be displayed properly)

-You are recommended to use the component and progressive frequency of digital RGB in case of using multi-vision function.

(It may not be displayed properly when using Video input and interlace frequency)

English

31/36

Image 34

Contents Page U.S.A EN60065 EN55022 1998+A1 2000 +A2 2003 CLASS A DECLARATION OF CONFORMITYAll of Digital sigange HYUNDAI IT provides EN55024 1998+A1 2001 +A2 EN 61000-3-2 2000 +A2DIGITAL SIGNAGE ContentsMajor features Safety Information The main plug of the power supply cord shall remain readily operable Do not hang on or jump to the product or mounting rack Be sure to understand Image quality of the productBase Frame Type Remote control & batteriesCheck the product list Users manualProper location for product installation Title and function of each part Control Panel5 8 0 @ $ Terminal panel3 4 6 7 9 ! # % How to insert batteries Remote control10/36 11/36 How to Connecting KioskSatellite receiver How to Connecting Digital RGBHDMI Horizontal frequency ResolutionSupport timing for HDMI Vertical frequencyHow to Connecting analog RGB PC D-SUB 14/36Support timing for PC How to Connecting the component Option 16/36Resolution Support timing for component & AVHow to Connecting the the video Option 18/36Adjusting OSD and explanation of its function How to Select the Picture ModeHow to Set the Desired Picture 20/36How to Select a Colour Tone 21/36How to Set the Display Size 22/36How to set image adjustment in PC mode Supported only in PC mode 23/36ReductionNR How to Set NoiseHow to Select the Audio ModeHow to Adjust the Desired Audio Mode How to Select Sound Mode How to Select Auto Volume26/36 How to Set Clock,Sleep Time, ON/OFF Time How to Reset27/36 Choosing the Your Languages 28/36How to Set Key-Lock How to set OSD tone29/36 How to Set the Multi Function Example of installation install 3x2 with 6 unitsSet up Value How to Set the Heat Control 32/36Diagnosis If the batteries are drained, replace them with new batteries 34/36of speaker cable the system as it supports Plug and PlayPower SpecificationsRecommended resolution D320MLI/G/D400ML D420MLI/G/P/T D460MLI/G/P/T/HD405MLI/G/D407MLI/G/P/T 2. REMOTE CONTROL WAVE FORM REMOTE CONTROL / RS232C COMMAND SPEC1. SPEED 9600 Baud/s, 8 bit, No parity, 1 Stop bit To power off set that is SET ID COMMAND TYPECommand example To factory reset all setCommand 5. COMMAND TYPEDescription 7. REMOTE CONTROL KEY CODE TABLE Key valueHYUNDAI IT Service Center