Hyundai P224WK manual Digital Signage, Be sure to understand, Image quality of the product

Page 8

Be sure to understand

	DIGITAL SIGNAGE

Be sure to understand	Image quality of the product
	CAUSE
		Due to the nature of LCD's property, Afterimage can occur. Afterimage appears when
		identical frames / images are displayed continuasly. If displayed for prolonged periods of
		time this can become permanent.
		PREVENTION
		When you display a freeze frame for a long time, lower the brightness and contrast
		(Brightness, 70/ Contrast, 80). Also it can be prevented by using moving frame.
		COUNTERMEASURES
	Temporary afterimage can be alleviated by displaying white or moving frame about 10
	hours.(But, permanent afterimage cannot be disappeared according to the property of
	LCD) This method is used to remove temporary afterimage that may occur after
	displaying a still frame for a certain time.
	It can take several minutes or hours to remove afterimage according to the severity. In
	the case that your cannot avoid displaying identical still image continuously, you can
	prevent it by displaying moving image for 2 or 3 minutes in every hour. As the brightness
	of still image and time of display are the cause of afterimage, you are recommended to
	lower the brightness in that case.

		!	Above problem shall not be covered by warranty.

English

/36

Image 8

Contents Page U.S.A DECLARATION OF CONFORMITY All of Digital sigange HYUNDAI IT providesEN60065 EN55022 1998+A1 2000 +A2 2003 CLASS A EN55024 1998+A1 2001 +A2 EN 61000-3-2 2000 +A2DIGITAL SIGNAGE ContentsMajor features Safety Information The main plug of the power supply cord shall remain readily operable Do not hang on or jump to the product or mounting rack Be sure to understand Image quality of the productRemote control & batteries Check the product listBase Frame Type Users manualProper location for product installation Title and function of each part Control Panel3 4 6 7 9 ! # % Terminal panel5 8 0 @ $ 10/36 Remote controlHow to insert batteries Satellite receiver How to Connecting Kiosk11/36 How to Connecting Digital RGBHDMI Resolution Support timing for HDMIHorizontal frequency Vertical frequencyHow to Connecting analog RGB PC D-SUB 14/36Support timing for PC How to Connecting the component Option 16/36Resolution Support timing for component & AVHow to Connecting the the video Option 18/36Adjusting OSD and explanation of its function How to Select the Picture ModeHow to Set the Desired Picture 20/36How to Select a Colour Tone 21/36How to Set the Display Size 22/36How to set image adjustment in PC mode Supported only in PC mode 23/36How to Set Noise How to Select the AudioReductionNR ModeHow to Adjust the Desired Audio Mode 26/36 How to Select Auto VolumeHow to Select Sound Mode 27/36 How to ResetHow to Set Clock,Sleep Time, ON/OFF Time Choosing the Your Languages 28/3629/36 How to set OSD toneHow to Set Key-Lock How to Set the Multi Function Example of installation install 3x2 with 6 unitsSet up Value How to Set the Heat Control 32/36Diagnosis 34/36 of speaker cableIf the batteries are drained, replace them with new batteries the system as it supports Plug and PlaySpecifications Recommended resolutionPower D320MLI/G/D400ML D420MLI/G/P/T D460MLI/G/P/T/HD405MLI/G/D407MLI/G/P/T 1. SPEED 9600 Baud/s, 8 bit, No parity, 1 Stop bit REMOTE CONTROL / RS232C COMMAND SPEC2. REMOTE CONTROL WAVE FORM COMMAND TYPE Command exampleTo power off set that is SET ID To factory reset all setDescription 5. COMMAND TYPECommand 7. REMOTE CONTROL KEY CODE TABLE Key valueHYUNDAI IT Service Center