JVC LT-26C31BUE, LT-26C31SUE manual Pixel defects, Distance recommendations, „ Cleaning the screen

Page 4

Pixel defects

LCDs use collections of fine points (“pixels”) to display images. While there is no problem with more than 99.99% of these pixels, please understand that a very small number of pixels may not light, or may light all the time.

Distance recommendations

Avoid improper installation and never position the unit where good ventilation is impossible.

When installing this TV, distance recommendations must be maintained between the set and the wall, as well as inside a tightly enclosed area or piece of furniture.

Keep to the minimum distance guidelines shown for safe operation.

150 mm

200 mm

150 mm

200mm

50 mm

Failure to take the following precautions may cause damage to the television or remote control.

DO NOT block the TV’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

DO NOT place anything on top of the TV.

(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)

DO NOT allow objects or liquid into the cabinet openings.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

DO NOT place any naked flame sources, such as lighted candles, on the TV.

DO NOT subject the TV to direct sunlight.

The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.

Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.

Never use any cleaner or detergent on it.

If there is a fault, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover.

„Cleaning the screen

The screen is coated with a special thin film to reduce reflection. If this film is damaged, uneven colors, discoloration, scratches, and other problems that cannot be repaired may occur. Pay attention to the following when handling the screen.

Do not use glue or adhesive tape on the screen.

Do not write on the screen.

Do not allow the screen to come in contact with any hard objects.

Do not allow condensation to form on the screen.

Do not use alcohol, thinner, benzene or other solvents on the screen.

Do not rub the screen hard.

CAUTION:

Operate only from the power source specified (AC 110 – 240 V, 50/60 Hz) on the unit.

Avoid damaging the AC plug and power cord.

When you are not using this unit for a long period of time, it is recommended that you disconnect the power cord from the main outlet.

The ambient temperature for using this unit is 0° to 40°C (32° to 104°F). Using the unit outside of this range may lead to it not working correctly or being broken.

D.I.S.T. demonstration

To start the D.I.S.T. demonstration:

Press the abutton to display the MENU (main menu). Then press the yellow button.

A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.

To quit the D.I.S.T. demonstration:

Press the yellow button, bbutton, P p buttons or any of the number buttons.

2

Image 4
Contents LT-26C31BUE LT-26C31SUE LT-26C31BJE LT-26C31SJE English Deutsch FrançaisHow to replace the fuse „ Warning„ If in doubt consult a competent electrician „ Guidelines for safe operationEnglish „ Cleaning the screen Pixel defectsDistance recommendations S.T. demonstrationContents Installation Setting up your TVUsing the stand Putting the batteries into the Remote control Remove the terminal coverConnecting the power cord to the AC outlet Connecting the aerial and video cassette recorder VCRWithout terminal covers Aerial Initial settings „ TV auto power on/VCR image view Link functions„ Pre-set download „ Direct RecTV buttons and functions Turn the TV on or off from standby mode Remote control buttons and functionsPress the #standby button to turn the TV on or off „ Use the PR List Watch images from external equipmentPR List „ Choose the Zoom mode „ Adjusting the visible area of the pictureZoom function 3D Sound functionUsing the PIP function Using the Freeze functionDisplaying the current time Return to TV channel instantlyUsing the MULTI-PICTURE function Operating a JVC brand VCR or DVD player„ To use Dbutton VCRUsing the List Mode Teletext functionBasic operation HoldCancel Sub-pageReveal SizeUsing the TV’s menu Picture Setting Picture ModePicture Adjustment Colour TempDigital VNR Picture FeaturesSuper DigiPure Colour System Movie TheatreAuto Aspect Colour ManagementSound Setting SpeakerStereo / I BBEVolume HeadphoneTV Speaker OutputEXT Setting S-VIDEO inputID List DubbingEXT-1/EXT-3 Features Sleep TimerBlue Back Child LockPress the Number buttons to enter the ID number Decoder EXT-2If you have forgotten the ID number Install LanguageAuto Program Choose LANGUAGE, then press the abuttonEDIT/MANUAL MoveInsert DeleteTo cancel the Insert function „ IDPress the red button to start the ID function Press the abutton to give a channel name ID to a TV channelTo cancel the Manual function When the Country setting is not United KingdomPress the green or red button to search for a TV channel Other TV channelsUsing the ACI function Downloading data to a VCR Additional menu operationsChanging the Country setting Using the Decoder EXT-2 functionTo return to the Install menu from the Country menu To cancel the Decoder EXT-2 functionConnecting external equipment Before connecting anythingAdditional preparation Without terminal covers„ Connecting headphones „ Video or sound signal output from the EXT-2 terminal„ Connecting Speakers/Amplifier „ T-V Link compatible VCRCH/CC numbers ChannelTroubleshooting „ Other concerns Specifications Design and specifications subject to change without noticeVictor Company of JAPAN, Limited